Manuals database logo
manualsdatabase
Your AI-powered manual search engine

Parker Compax3 S025 V2 manuals

Compax3 S025 V2 first page preview

Compax3 S025 V2

Brand: Parker | Category: DC Drives
Table of contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. Introduction
  6. Type specification plate
  7. Release 1/2004
  8. New machine zero modes
  9. C3 MotorManager: configuration of almost any motors
  10. Safety Instructions
  11. Special safety instructions
  12. Conditions of utilization
  13. Conditions of utilization for UL permission
  14. Compax3 I11 T11: Positioning via digital I/Os
  15. Compax3 device description
  16. Plug and connector assignment Compax3
  17. Function of the LEDs on the front panel
  18. Power supply plug X1 for 400 VAC devices
  19. Ballast resistor / high voltage supply plug X2 for 400VAC devices
  20. Motor / Motor brake (plug X3)
  21. Control voltage 24VDC / enable (plug X4)
  22. RS232 / RS485 interface (plug X10)
  23. Analog / Encoder (plug X11)
  24. Digital inputs/outputs (plug X12)
  25. Output wiring of digital outputs
  26. Installation and dimensions Compax3
  27. Installation and dimensions of Compax3 S038 and S075 V4
  28. Installation and dimensions of Compax3 S150 V4
  29. Installation and dimensions of Compax3 S300 V4
  30. Setting up Compax3
  31. Motor selection
  32. Optimize motor reference point and switching frequency of the power output stage
  33. Ballast resistor
  34. General drive
  35. Measure reference
  36. Machine reference modes (MN-Ms)
  37. Adjusting the machine zero proximity switch
  38. Software end limits
  39. Defining jerk / ramps
  40. Ramp upon error / deenergize
  41. Limit and monitoring settings
  42. Tracking error limit
  43. Encoder simulation
  44. Positioning
  45. Define positioning data records
  46. Dynamic positioning
  47. Configuration name / comments
  48. Test commissioning Compax3
  49. Device status
  50. Optimization
  51. Stiffness of the speed controller
  52. Damping of the speed controller
  53. Advanced control parameters
  54. Commissioning mode
  55. Turning the motor holding brake on and off
  56. I11 T11 192-120101 N6 - March
  57. Binary record
  58. Status values
  59. Device
  60. Positions
  61. Speeds
  62. Currents
  63. Inputs
  64. IEC61131-3
  65. Transmitter
  66. Error
  67. Compax3 Accessories
  68. Accessories order code
  69. Parker servo motors
  70. Linear motors
  71. Rotary servo motors
  72. Motor data table for standard motors
  73. Holding brake
  74. Dimensions of the SMH(A)-motors
  75. Dimensions of the MH(A)105-motors
  76. Dimensions of the MH(A)145 and MH(A)205 motors
  77. Order code for SMH/MH motors
  78. Connections to the motor
  79. SinCos cable
  80. Motor cable with plug
  81. Motor cable for terminal box
  82. EMC measures
  83. Mains filter NFI01/02
  84. Motor output filter
  85. Wiring of the motor output filter
  86. External ballast resistors
  87. BRM8/01 ballast resistors
  88. Ballast resistor BRM4/0x
  89. Operator control module BDM
  90. EAM06 terminal block for inputs and outputs
  91. ZBH plug set
  92. Interface cable
  93. RS485 cable to Pop
  94. I/O interface X12
  95. Ref X11
  96. Encoder cable
  97. Technical Data
  98. Index
Compax3 S025 V2 first page preview

Compax3 S025 V2

Brand: Parker | Category: Industrial Electrical
Table of contents
  1. Notes on the Documents Supplied
  2. C3 ServoManagers
  3. Table Of Contents
  4. Table Of Contents
  5. Table Of Contents
  6. Type specification plate
  7. Release 1/2004
  8. New machine zero modes
  9. C3 MotorManager: configuration of almost any motor
  10. Safety Instructions
  11. Special safety instructions
  12. Conditions of utilization
  13. Conditions of utilization for UL certification
  14. Manufacturer's Declaration of Conformity
  15. Compax3 device description
  16. Plug and connector assignment Compax3
  17. Function of the LEDs on the front panel
  18. Power supply plug X1 for 400 VAC devices
  19. Ballast resistor / high voltage supply plug X2 for 400VAC devices
  20. Motor / Motor brake (plug X3)
  21. Control voltage 24VDC / enable (plug X4)
  22. RS232 / RS485 interface (plug X10)
  23. Analog / Encoder (plug X11)
  24. Wiring of the analog input
  25. Output wiring of digital outputs
  26. Resolver / Feedback (connector X13)
  27. Installation and dimensions Compax3
  28. Installation and dimensions of Compax3 S038 and S075 V4
  29. Installation and dimensions of Compax3 S150 V4
  30. Installation and dimensions of Compax3 S300 V4
  31. Safety function – safe standstill
  32. Safety instructions for the "safe standstill" function
  33. Application examples for "safe standstill
  34. Sample circuit example of Compax3 devices with fieldbus option
  35. Sample circuit for C3 powerPLmC multi-axis application
  36. Technical Data
  37. Index
  38. N7 - February
Related products
Compax3 S063 V2Compax3 S075 V4Compax3 S038 V4Compax3S025V2Compax3 S150 V4Compax3 S300 V4Compax3 SeriesCompax3SCompax3S063V2Compax3S100V2
Parker categories
Control Unit
Controller
Water Filtration Systems
Dryer
Engine
Industrial Equipment
Servo Drives
DC Drives
Water Pump
Chiller
More Parker categories
Manuals database logo
manualsdatabase
Your AI-powered manual search engine