Oki c831n User Manual

Also see for C831dn: Safety and Warranty Guide User manual User manual

Contents

Oki c831n User Manual Manual pdf 17 page image

- 17 -1 1. Convenient Print FunctionsPrinting on Custom Size PaperYou can register a customized paper size on theprinter driver so you can print on nonstandardpaper such as banners.● Settable custom size rangeWidth: 64 to 297 mmLength: 90 to 1320.8 mmPaper sizes that can be fed differ depending onthe tray.Note● Register the paper size as portrait, and load paper inportrait orientation.● For banner media that is over 432 mm long, use thefaceup stacker.● This function may not be available in some applications.● If paper length exceeds 432 mm, we do not guaranteeprint quality.● If paper is so long that it exceeds the paper supports ofthe MP tray, support it by hand.● When using tray 1 or tray 2/3/4, select the <ENTER>button on the operator panel>[Menus]>[Tray Configuration]>[Using Tray Config]>[Paper Size]>[Custom] before doing the followingprocedure.● If images are not correctly printed on large size paper,selecting [Standard (600x600dpi)] for [Print Quality],image in the PS printer driver may allow for correctprinting.● Use of paper with a width of less than 100 mm is notrecommended. Doing so may cause paper jams.Reference● For details on the paper sizes that can be fed on each trayor used for duplex printing, refer to the User’s Manual(Setup).● The [Auto Tray Change] is enabled by default. Whenthe tray runs out of paper during printing, the printerautomatically begins feeding paper from that tray. If youwant to feed custom paper only from a particular tray,disable auto tray switching. For auto tray change, refer to"Auto Tray Switching" P.34. Specifying Custom SizesTo load custom size paper, you need to registerthe width and length of the paper beforeprinting. The range of the sizes you can setdiffers according to the paper tray.Tray Available size rangeTray1 Width:105 to 297 mm (4.1 to 11.7 inches)Length:148 to 431 mm (5.8 to 17.0 inches)Tray2/3/4(Option)Width:148 to 297 mm (5.8 to 11.7 inches)Length:182 to 431 mm (7.2 to 17.0 inches)Tray Available size rangeMP tray Width:64 to 297 mm (2.5 to 11.7 inches)Length:90 to 1321 mm (3.5 to 52.0 inches)Note● You can configure the [Custom] setting only when[Paper Size] is set to [Custom].● The available size range for duplex printing is the same asthat for tray 2.1 Press the <ENTER> button on theoperator panel.2 Press the scroll button several timesto select [Menus] and press the<ENTER> button.3 Check that [Tray Configuration]is selected and press the <ENTER>button.4 Press the scroll button several timesto select [Tray Config] of the papertray in which you loaded paper and thenpress the <ENTER> button.5 Check that [Paper Size] is selected andpress the <ENTER> button.6 Press the scroll button several timesto select [Custom] and then press the<ENTER> button.7 Press the <BACK> button.8 Press the scroll button to select[X Dimension] and then press the<ENTER> button.9 Enter the paper width value usingthe ten-key pad and then press the<ENTER> button.10 Press the <BACK> button.11 Press the scroll button to select[Y Dimension] and then press the<ENTER> button.12 Enter the paper length value usingthe ten-key pad and then press the<ENTER> button.13 Press the <ON LINE> button to exit themenu mode.