Panasonic LP-M Series Serial Communication Manual
Also see for LP-S Series: Operation manualMaintenance GuideManual
                                                                                                                                                                                                            | |
Contents
|
111■ Test marking: TST[Supported models: LP-Mxxx/LP-Sxxx]Performs the test marking and measures the marking energy [mJ] and period.Execute test markingDesignates the start of the test markingSTX TST S [Test marking mode]Max. 1-byte (Check sum) DelimiterReadout request of test marking resultSTX TST R (Check sum) DelimiterReadout dataSTX TST A [Marking energy] [Marking time]15-byte (Check sum) DelimiterName Data length[byte] Description RemarksTest markingmode (1)“0”: Marking energy error detection“1”: Marking energy error notdetectedPerforms test marking upon commandreception.Set whether to detect the marking energy errorafter test marking.This setting is omissible. If this is omitted, “0”:marking energy error is indicated.Marking energy 9 “000000000”–“999999999” [mJ]Marking time 6• Marking time 100 seconds ormore: “0100.0”–“9999.9” [s]• Marking time less than 100seconds: “000.01”–“099.99” [s]When the marking time is 100 seconds or more,the number of decimal places should be 1 andwhen it is less than 100, it should be 2.Reference• When the test marking is performed, the marking operation is started by actual laser radiation.• For test marking, the counter value is not changed even when a counter is set.• This command is not acceptable when the No. 2 DIP switch on the back surface of controller is turned to OFF.• This command can be transmitted when laser pumping is turned ON and the shutter is closed. Response data forabnormal receiving (NAK03 or NAK99) is returned when the laser pumping is OFF or the shutter is opened. Even whenthe “reception mode ON” is set for the command reception permission: MKM command, it is refused if the shutter isopened.• When the Marking Status Sending Enable (MST/MKR) is set to on, the marking status is transmitted after the marking iscompleted.• Transmit the test marking result readout command after the marking end output of the output terminal is turnedON following the test marking execution command, or after response to the marking status if the “Marking StatusTransmission Permission (MST Command)” is set.• For LP-Mxxx-S type, laser can not be emitted without opening the laser gate. After starting the test marking, open thelaser gate by external control signals. Refer to the “Safety / Setup / Maintenance Guide” for detail.• For LP-Mxxx-S type, “laser gate open request output” signal will be ON to start the test marking and “laser gate closerequest output” signal will be ON after finishing the marking for the specified one-shot time.ME-LPMSZ-SR-9 |
Related manuals for Panasonic LP-S Series
This manual is suitable for:
LP-S SeriesLP-M SeriesLP-M200LP-M200-CHNLP-M200-SLP-M200-S-CHNLP-M205LP-M205-CHNLP-M205-SLP-M205-S-CHNLP-M500LP-M500-CHNLP-M500-SLP-M500-S-CHNLP-M505LP-M505-CHNLP-M505-SLP-M505-S-CHNLP-MA00LP-MA00-CHNLP-MA05LP-MA05-CHNLP-MA05-SLP-MA05-S-CHNLP-MA06LP-MA06-CHNLP-MA06-SLP-MA06-S-CHNLP-S200LP-S200-CHNLP-S200-SFLP-S202LP-S202-CHNLP-S202-SFLP-S205LP-S205-CHNLP-S205-SFLP-S500LP-S500-CHNLP-S500-SFLP-S500WLP-S500W-CHNLP-S502LP-S502-CHNLP-S502-SFLP-S505LP-S505-CHNLP-S505-SFLP-S505WLP-S505W-CHNLP-Z SeriesLP-Z130LP-Z130-CHNLP-Z250LP-Z250-CHNLP-Z256LP-Z256-CHN
manualsdatabase
Your AI-powered manual search engine