Panasonic LP-M Series Serial Communication Manual
Also see for LP-S Series: Operation manualMaintenance GuideManual
                                                                                                                                                                                                            | |
Contents
|
147■ VEC logo conditions (CAD condition) : CDCSets the marking condition of VEC (work shape converted for laser marker) logo file.Setting / Readout data of VEC logoSTX CDC Subcommand[CAD No.] [X position] [Y position] [Scale] [Rotation angle][Laser pulse cycle correction] [Scan speed correction][Laser pulse cycle correction]36-byte (LP-F10 mode), 33-byte (LP-F10W mode)(Check sum) DelimiterSub command is “S” at the time of setting and “A” for response data at the time of readout.Readout request out of VEC logoSTX CDC R [CAD No.]2-byte (Check sum) DelimiterName Data length[byte] Description RemarksCAD No. 2 “00”–“15”X position 7“-300.00”–“+300.00” [mm] Specifies the origin coordinate of the logo.Y position 7Magnification 5Model type* Setting range [times]LP-Sxx0 “00.10”–“01.98”LP-Sxx5 “00.10”–“03.53”LP-Sxx2 “00.10”–“01.21”LP-Sxx0W “00.10”–“02.27”LP-Sxx5W “00.10”–“04.04”LP-Mxx0/LP-Zxx0 “00.10”–“03.03”LP-Mxx5 “00.10”–“05.56”LP-Mxx6/LP-Zxx6 “00.10”–“08.34”Rotation angle 6 “-180.0”–“+180.0” [°] The angle of rotation centering on theorigin position of CAD file, is indicated.Laser powercorrection 3 “000”–“200” [%]• The correction ratio is calculated usingthe value set at the laser condition as100%.• Laser Pulse Cycle Correction can bespecified only in LP-F10 mode.Scan speedcorrection 3 “050”–“200” [%](Laserpulse cyclecorrection)(3) “050”–“200” [%]* For the detail of the model type, refer to “Target laser marker” (P.4).Reference• Logo file for the LP-F series is treated as one for LP-F10/F10W (marking area 90 mm x 90 mm). Logo file used forspecial-order model (marking area other than 90 mm x 90 mm) is not supported.• When a logo file for the LP-F series is used, X/Y scales are automatically adjusted to the same size in the LP-M/LP-S/LP-Z series. X/Y scales for readout of CAD condition may be different from values specified in CAD condition setting.• In readout response, the digit of 1 μm or 0.01° is rounded down.• The laser power correction, speed scan correction and laser pulse cycle correction are out of the setting range of theLP-F10/F10W, readout cannot be performed. (NAK15 is returned.)• When the setting is performed using this command, the layer No. is “0”.• Setting with this command in the LP-F10W mode, the laser pulse cycle correction is set to 100%.• For LP-SxxxW type, the laser pulse cycle correction setting does not affect the marking. Also this setting is not saved inthe file.ME-LPMSZ-SR-9 |
Related manuals for Panasonic LP-S Series
This manual is suitable for:
LP-S SeriesLP-M SeriesLP-M200LP-M200-CHNLP-M200-SLP-M200-S-CHNLP-M205LP-M205-CHNLP-M205-SLP-M205-S-CHNLP-M500LP-M500-CHNLP-M500-SLP-M500-S-CHNLP-M505LP-M505-CHNLP-M505-SLP-M505-S-CHNLP-MA00LP-MA00-CHNLP-MA05LP-MA05-CHNLP-MA05-SLP-MA05-S-CHNLP-MA06LP-MA06-CHNLP-MA06-SLP-MA06-S-CHNLP-S200LP-S200-CHNLP-S200-SFLP-S202LP-S202-CHNLP-S202-SFLP-S205LP-S205-CHNLP-S205-SFLP-S500LP-S500-CHNLP-S500-SFLP-S500WLP-S500W-CHNLP-S502LP-S502-CHNLP-S502-SFLP-S505LP-S505-CHNLP-S505-SFLP-S505WLP-S505W-CHNLP-Z SeriesLP-Z130LP-Z130-CHNLP-Z250LP-Z250-CHNLP-Z256LP-Z256-CHN
manualsdatabase
Your AI-powered manual search engine