Panasonic P2HD AJ-HPX3100G Operating Instructions Manual

Also see for AJ-HPX3100G: Manual Operating instructions

Contents

80 Adjustments and Settings for Recording : Viewfinder Screen Status DisplaysInformation Item Indication Status13. System informationand warningsSYSTEM ERROR-¢¢TURN POWER OFFCARD ERR ¢REC WARNINGOVER MAX# CLIPSTEMPORARY PAUSEBACKUP BATT EMPTYFAN STOPWIRELESS-RFEOMBOSEOSCANNOT RECCANNOT PLAYCOMM ERRORTEXT MEMOTEXT MEMO INVALIDMARK ON/OFFSHOT MARK INVALIDUPDATINGUSB DEVICEUSB HOSTTHUMBNAIL OPENCLIP DISCONTINUEDTC REGENSLOT SELECTSLOT SELECT INVALIDDIR NG CARDSLOT1/2RUN DOWN CARDSLOT1/2REAR XR AUTOSomething abnormal is happening to the internal computer communications orreference signal. No further recording or playback can be performed. ¢¢ isreplaced with an error code. For more information, see [Error Codes] (page 155).P2 card has been removed while being accessed (recorded, played back, orformatted), and subsequent operation is disabled.An error has occurred while recording data to or playing data from a P2 card.In the actual indication the ¢ is replaced by the slot number of the P2 card thattriggered the error.Something abnormal is happening to video and/or audio being recorded.Displayed when the maximum number of clips (1000) recorded to the P2 cardis exceeded.There is a temporary halt in recording due to distortion in reference signalssuch as during GENLOCK input.Backup battery needs replacing.The fan is locked and halted.RF signal from the wireless receiver is degraded.P2 card has no free space.Playback position is at the start of all the clips.Playback position is at the end of all the clips.The P2 card is not recordable. Detailed information is provided on theFUNCTION screen of MODE CHECK.> [Displays in mode check only] (page 82)Clip cannot be played back perhaps because no P2 card is loaded, or the P2card contains no clips.Displayed when disconnection between microcomputers continues for aspecified period or longer.Text memo has been added.Text memo has not been successfully added.Shot mark been added or deleted. For information on shot marks, see [ShotMark Function] (page 46).This is displayed when shot marks cannot be added.Clip information is being updated. Playback operation disabled.AJ-HPX3100 is in USB DEVICE mode. When communication is disabled, theindication blinks.Indicates that the camera-recorder is set to the USB HOST mode. When theexternal hard disk is not successfully recognized, then the indication blinks.Thumbnail is being manipulated.Displayed when the consistency of the combined clip is disrupted andsubsequent recordings cannot be combined in the clip when recording in ONECLIP REC mode.The RET button was pressed to regenerate the time code as the time code forthe last clip recorded on a P2 card.This blinks while the recording slots of P2 cards are switched after pressingthe USER switch where the SLOT SEL function is assigned.This is displayed if the recording slots of P2 cards cannot be switched whenthe USER switch where the SLOT SEL function is assigned is pressed.This is displayed when the recording starts or completes while a P2 card withan irregular directory arrangement is inserted or data are recorded afterinserting an irregular P2 card.This is displayed when the recording starts or completes with a P2 card onwhich the maximum number of overwrites has been exceeded, or when datais recorded after inserting such a P2 card.The AUDIO IN switch is disabled because audio input automatically goes tothe rear XLR connector.14. Time code indication TCG 12:59:59:20TCR 12:59:59:20(V)UBG AB CD EF 00(V)UBR 12 34 56 78CTL –1:59:59:20TCG (time code generator value)TCR (time code reader value)UBG VUBG (User bits generator value)UBR VUBR (User bits reader value)Displays CTL count.15. Chromatic aberrationcompensationCAC Displayed when chromatic aberration compensation is activated16. Extender EX Lens extender used.17. Color temperature ¢.¢K Color temperature assigned to A, B, and PRST of the WHITE BAL switch (thisis a value stored at AWB performance or a value set through the menuoption). The indication is not provided in ATW mode.18. Filter position 1 - 4A - D(blink)This indicates the position of the ND filter.This indicates the position of the CC filter.This indicates that the filter has not been set to a proper position.19. Dynamic rangestretcher modeDRS This appears when the video level of a part with high brightness iscompressed, and the function stretching the dynamic range is selected.