Carrier AquaEdge 19XR Series Start-up, Operation And Maintenance Instructions Manual

Also see for AquaEdge 19XR series: Installation instructions Start-up, operation and maintenance instructions

Contents

CL-6- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - -CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE19XR PIC 6 OPTION CONFIGURATION TABLE (CONF_OPT) CONFIGURATION SHEETDESCRIPTION RANGE UNITS DEFAULT VALUEAuto Restart Option DSABLE/ENABLE DSABLECommon Sensor Option DSABLE/ENABLE DSABLEEC Valve Option0 = No, 1= Cont2 = On/Off, 3 = 4-20 mA0 to 3 0EC Valve Selection0 = Disable, 1 = Surge2 = Low Load, 3 = Comb0 to 3 0ECV Open IGV1 Position 0.5 to 10 % 5.0ECV Close IGV1 Position 1.5 to 20 % 10.0ECV Off DT for Low Load 0.5 to 10.0 ^F 4.0ECV On DT for Low Load 0.5 to 10.0 ^F 2.0ECV Low Load DB 0.5 to 2.0 ^F 1.0Head Pres Valve Option DSABLE/ENABLE DSABLEHead Pres Delta P 0% 20.0 to 85.0 psig 25.0Head Pres Delta P 100% 20.0 to 85.0 psig 50.0Head Pressure Min Output 0.0 to 100.0 % 0.0Head Pressure Deadband, 0-10 1Tower Fan High set point 55 to 105 75Refrigerant Leak Option DSABLE/ENABLE DSABLERefrig Leakage Alarm mA 4 to 20 20Oil EXV Option DSABLE/ENABLE mA DSABLEOil Temp High Threshold 100 to 140 °F 120Oil Temp Low Threshold 90 to 130 °F 110Gas Torque Factor 0.25 to 3.0 °F 1Guide Vane/SRD Factor 0.7 to 1.20 0.95Power Recovery Timeout 0 to 60 min 15Condenser Flush Alert DSABLE/ENABLE DSABLECustomer Alert Option DSABLE/ENABLE DSABLEIce Build Option DSABLE/ENABLE DSABLEIce Build Recycle DSABLE/ENABLE DSABLEIce Build Termin Source0 = Temp, 1 = Contact, 2 = Both 0 to 2 0Water Pressure Option0=No, 1=Pres., 2=Pres. D. 0-2,0,Water Flow Measurement0 = No, 1 = Flow Meter, 2 = FlowSwitch0-2 0Water Flow Determination0=Sat Temp, 1=Flow Switch. 0-1 0Water Flow Determination(0=Sat Temp, 1=Flow Switch) 0-1 0Water Flow at 4 mA 0-12000 GPM 0.00Water Flow at 20mA 0-12000 GPM 0.00Evap Flow Rate Baseline 0-9000 GPM 0.00Evap Pres Drop Baseline 0-20 PSI 0.00Cond Flow Rate Baseline 0-9000 GPM 0.00Cond Pres Drop Baseline 0-20 PSI 0.00Water Pres Drop @ 20mA 0-40 PSI 10.00Vapor Source SV Delay 0-10 min 5.0Max Oil Pressure Diff 35-60 PSI 50Oil Pump VFD Max Step 0-10 % 7Vapor Source SV Delay 0-10 min 5Vapor Source SV Option DSABLE/ENABLE DSABLEEvap Liquid Temp Opt DSABLE/ENABLE EnableEvap App Calc SelectionSat Temp = 0, Ref Temp = 1 0/1 1Remote Stop Contact DSABLE/ENABLE DSABLE