Denon AVR-4520CI Owner's Manual

Also see for AVR-4520CI: Getting started guide Specification Model information Service manual

Contents

141Manual Setup Default settings are underlined.Perform when setting the speakers manually or when changing settings made in Audyssey® Setup.• If you change the speaker settings after performing Audyssey® Setup, it will not be possible to selectAudyssey MultEQ® XT 32, Audyssey Dynamic EQ® and Audyssey Dynamic Volume® (vpage 125,126).• “Manual Setup” can be used without changing the settings. Please set if necessary.Setting items Setting detailsAmp AssignSelect power amplifierusage method to matchyour speaker system.For the flow to set “AmpAssign”, see page 140.Assign Mode : Set the assignment mode.• 9.1ch(SB/FH/FW) : Assigns all power amplifiers within this unit forMAIN ZONE.• 7.1ch + ZONE2 : Assigns power amplifiers within this unit as follows:7.1ch for MAIN ZONE and 2ch for ZONE2.• 5.1ch + ZONE2/3 : Assigns power amplifiers within this unit as follows:5.1ch for MAIN ZONE and 2ch for ZONE2 and ZONE3 each.• 7.1ch + ZONE2/3-MONO : Assigns power amplifiers within this unitas follows: 7.1ch for MAIN ZONE and 1ch for ZONE2 and ZONE3 each.• 7.1ch(Bi-Amp) : Assigns power amplifiers within this unit as follows:7.1ch for MAIN ZONE and 2ch for the front speaker bi-amplifierconnection.• 5.1ch(Bi-Amp) + ZONE2 : Assigns power amplifiers within this unit asfollows: 5.1ch for MAIN ZONE, 2ch for the front speaker bi-amplifierconnection, and 2ch for ZONE2.• 9.1ch/2ch Front : Assigns all power amplifiers within this unit for MAINZONE. Up to 9.1ch playback is available. You can also use a front speakerthat is different from the one used during multi-channel playback forplayback by switching the internal power amplifier during 2ch playback.• 7.1ch/2ch Front(Bi-Amp) : Assigns power amplifiers within this unitas follows: 7.1ch for the MAIN ZONE multi-channel playback. You canalso use a front speaker that is different from the one used during multi-channel playback for playback under the bi-amplifier connection byswitching the internal power amplifier during 2ch playback.• 7.1ch + Front B : Assigns power amplifiers within this unit as follows:7.1ch for MAIN ZONE and 2ch for the second front speaker connection.• Discrete 11.1ch : Assigns 9.1ch for power amplifiers within this unit and2ch (front/front height) for the external power amplifier connection. Upto 11.1ch playback is available.• Pre Amplifier : Connects all speakers by using an external poweramplifier and uses this unit as a preamplifier. Up to 9.1ch playback isavailable.• Custom : Assigns power amplifiers within this unit as you prefer.Setting items Setting detailsAmp Assign(Continued)The following setting items are displayed according to the setting specifiedfor“Assign Mode” (vpage 141).n When “Assign Mode” (vpage 141) is set to “9.1ch(SB/FH/FW)”, “7.1ch+ ZONE2”, “7.1ch + ZONE2/3-MONO”, “7.1ch(Bi-Amp)”, “9.1ch/2ch Front”,“7.1ch/2ch Front(Bi-Amp)” or “7.1ch + Front B”Main Speakers : Selects speakers used in MAIN ZONE.• S.Back/F.Height : Uses surround back and front height speakers.• S.Back/F.Wide : Uses surround back and front wide speakers.• F.Height/F.Wide : Uses front height and front wide speakers.n When “Assign Mode” (vpage 141) is set to “Discrete 11.1ch”Main Pre-amps : Selects the PRE OUT connector that is connected tothe external power amplifier used in MAIN ZONE.• Front : Connects the PRE OUT connector for the front speaker.• Front Height : Connects the PRE OUT connector for the front heightspeaker.n When “Assign Mode” (vpage 141) is set to “Pre Amplifier”Pre-Amp Assign : Selects how to use the PRE OUT connector.• All : Uses this unit as a preamplifier by using only the PRE OUTconnector without using the power amplifiers within this unit.• Custom : Sets whether to use each channel as a preamplifier or usespeakers.Center / Surround / Surr. Back / Front Height / Front Wide• Speaker : Select to use speakers.• Pre-amp out : Select to output audio only from the PRE OUTconnectors.n When “Assign Mode” (vpage 141) is set to “Custom”Output Channel : Selects signals output from the selected speakerconnector.• Front / Center / Surround / Surround Back / Front Height / FrontWide / ZONE2 / ZONE3 / ZONE2/3• None : Does not output audio from the selected speaker.Speakers