Denon AVR-4520CI Owner's Manual

Also see for AVR-4520CI: Getting started guide Specification Model information Service manual

Contents

143SpeakersSetting items Setting detailsDistancesSet distance from listeningposition to speakers.Measure beforehand thedistance from the listeningposition to each speaker.Unit : Set the unit of distance.• Feet / MetersStep : Set the minimum variable width of the distance.• 1ft / 0.1ft• 0.1m / 0.01mSet Defaults : The “Distances” settings are returned to the defaultsettings.• Reset : Reset to the defaults.• Cancel : Do not reset to the defaults.When you select “Set Defaults” and pressENTER, the “Resets all of the distancesettings to the factory defaults?” prompt isdisplayed. Select either “Reset” or “Cancel”,and press ENTER.Front L / Front R / F. Height L / F. Height R / F. Wide L / F. Wide R /Center / Subwoofer 1z1 / Subwoofer 2z1 / Surround L / Surround R /Surr. Back Lz2 / Surr. Back Rz2 : Select speaker for distance setting.z1 When the “Speaker Config.” – “Subwoofer” setting (vpage 142)is set to “1spkr”, “Subwoofer” is displayed.z2 When the “Speaker Config.” – “Surr. Back” setting (vpage 142)is set to “1spkr”, “Surr. Back” is displayed.• 0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.• The speakers that can be selected differ depending on the “Amp Assign”(vpage 141) and “Speaker Config.” (vpage 142) settings.• Default settings :Front L / Front R / F. Height L / F. Height R / Front Wide L / Front Wide R /Center / Subwoofer 1 / Subwoofer 2 : 12.0 ft (3.60 m)Surround L / Surround R / Surr. Back L / Surr. Back R : 10.0 ft (3.00 m)• Set the difference in the distance between the speakers to less than20.0 ft (6.00 m).NOTESpeakers set to “None” in “Speaker Config.” (vpage 142) are notdisplayed.Setting items Setting detailsLevelsSet the volume of the testtone to be the same when itis output from each speaker.Test Tone Start : Output test tone.• Front L / F. Height L / Center / F. Height R / Front R / F. Wide R /Surround R / Surr. Back Rz1 / Surr. Back Lz1 / Surround L /F. Wide L / Subwoofer 1z2 / Subwoofer 2z2 / Subwoofer 1+2z3 :A test tone is output from the selected speaker. While listening to thetest tone, adjust the volume output from the selected speaker.z1 When the “Speaker Config.” – “Surr. Back” setting (vpage 142)is set to “1spkr”, “Surr. Back” is displayed.z2 When the “Speaker Config.” – “Subwoofer” setting (vpage 142)is set to “1spkr”, “Subwoofer” is displayed.z3 When “Subwoofer 1+2” is selected, you can adjust the volume ofSubwoofer 1 and Subwoofer 2 at the same time.• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.When “Levels” is adjusted, the adjusted values are set for all thesound modes.NOTE• Speakers set to “None” in the “Speaker Config.” (vpage 142)settings are not displayed.• When a headphones jack is inserted in the PHONES jack of this unit, the“Levels” is not displayed.Set Defaults : The “Levels” settings are returned to the default settings.• Reset : Reset to the defaults.• Cancel : Do not reset to the defaults.When you select “Set Defaults” and pressENTER, the “Reset all of the channel levelsettings to the factory defaults?” prompt isdisplayed. Select either “Reset” or “Cancel”,and press ENTER.