Contents - Introduction
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Machine Specifications
- Performance Specifications
- Hydraulic Component Specifications
- Valve Coil Resistance Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Pre-Delivery Preparation
- Maintenance Inspection Report
- A-1 Inspect the Manuals and Decals
- A-2 Perform Pre-operation Inspection
- A-4 Perform Function Tests
- A-6 Check the High Pressure Hydraulic Filter Condition Indicator
- A-8 Perform Engine Maintenance - Deutz and Continental Models
- A-10 Grease the Turntable Rotation Bearing and Rotate Gear
- A-11 Perform Engine Maintenance
- A-12 Replace the Drive Hub Oil
- A-13 Perform Engine Maintenance - Perkins Models
- B-1 Inspect the Battery(s)
- B-2 Inspect the Electrical Wiring
- B-3 Test the Key Switch
- B-5 Inspect the Engine Air Filter
- B-6 Check the Oil Cooler and Cooling Fins - Deutz Models
- B-7 Confirm the Proper Brake Configuration
- B-10 Check and Adjust the Engine RPM
- B-11 Perform Engine Maintenance
- B-13 Test the Ground Control Override
- B-15 Test the Engine Idle Select Operation
- B-16 Test the Fuel Select Operation - Gasoline/LPG Models
- B-17 Test the Drive Enable System
- B-18 Test the Drive Brakes
- B-20 Test the Drive Speed - Raised or Extended Position
- B-21 Test the Alarm Package (if equipped) and the Descent Alarm
- B-22 Inspect the Fuel and Hydraulic Tank Cap Venting Systems
- B-23 Perform Hydraulic Oil Analysis
- C-2 Grease the Platform Overload Mechanism (if equipped)
- C-3 Test the Platform Overload System (if equipped)
- C-5 Replace the Fuel Filter/ Water Separator Element - Diesel Models
- C-6 Check the Safety Envelope Limit Switches and Angle Sensor, S-80X
- D-1 Check the Boom Wear Pads
- D-2 Check the Free-wheel Configuration
- D-3 Check the Turntable Rotation Bearing Bolts
- D-5 Perform Engine Maintenance
- D-7 Replace the Drive Hub Oil
- D-8 Perform Engine Maintenance - Deutz Models
- E-1 Test or Replace the Hydraulic Oil
- E-2 Perform Engine Maintenance - Perkins Models
- ALC-500 Circuit Board
- Joysticks
- Platform
- Platform Leveling Slave Cylinder
- Platform Rotator
- Calibrate the Platform Overload System
- Jib Boom Components,
- Function Manifold Components
- Valve Adjustments - Function Manifold
- Brake/Two-speed Manifold Components
- Turntable Rotation Manifold Components
- Platform Rotate Manifold Components
- Platform Manifold Components, S-80
- Platform Manifold Components, S-85
- WD Traction Manifold Components
- Drive Oil Diverter Manifold Components (welder option)
- Valve Adjustments - Traction Manifold
- Valve Coils
- Fuel Tank
- Hydraulic Tank
- Turntable Rotation Drive Hub Assembly
- Yoke and Hub
- Steer Cylinder
- Yoke and Drive Hub
- Drive Motor
- Steer Cylinders
- Oscillate Axle Cylinders
- Oscillate Directional Valve
- Fault Codes - Control System
- Electrical Symbols Legend
- Hydraulic Symbols Legend
- Connector Pin Legend - View 1
- Connector Pin Legend - View 2
- Deutz TD2011L04i Models
- Platform Control Box Wiring Diagram, S-80 and S-85 (ANSI / CSA / AS Deutz TD2011L04i Models
- Electrical Schematic, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Deutz TD2011L04i Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Electrical Schematic, S-80X Deutz TD2011L04i Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Deutz TD2011L04i Models
- Platform Control Box Wiring Diagram, S-80X Deutz TD2011L04i Models
- Electrical Schematic, S-80 and S-85 (ANSI / CSA / AS Perkins 804D-33 Models
- Perkins 804D-33 Models
- Electrical Schematic, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Perkins 804D-33 Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Electrical Schematic, S-80X Perkins 804D-33 Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Perkins 804D-33 Models
- Platform Control Box Wiring Diagram, S80X Perkins 804D-33 Models
- Platform Control Box Switch Panel Wiring Diagram, S80X Perkins 804D-33 Models
- Continental TME27 Models
- Ground Control Box Terminal Strip Wiring Diagram S-80 and S-85 (ANSI / CSA / AS), Continental TME27 Models
- Platform Control Box Wiring Diagram, S-80 and S-85 (ANSI / CSA / AS Continental TME27 Models
- Electrical Schematic, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Continental TME27 Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Electrical Schematic, S-80X Continental TME27 Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Continental TME27 Models
- Platform Control Box Wiring Diagram, S-80X Continental TME27 Models
- Continental TME27 Engine Harness
- Platform Level Cutout, CTE Option
- Continental Options Schematic
- Deutz and Perkins Options Schematic
- kW Hydraulic Generator Wiring Diagram
- kW Hydraulic Generator Electrical Schematic
- Belt Driven Generator Option
- Relay and Fuse Panel Legend
- Hydraulic Schematic, 2WD Models
- Hydraulic Schematic, 4WD Models
- kW Hydraulic Generator Hydraulic Schematic
|
Section 4 • Repair Procedures4 - 10 S-80 • S-85 • S-80X Part No. 122985February 2012PLATFORM COMPONENTS2-2Platform Leveling Slave CylinderThe slave cylinder and the rotator pivot are thetwo primary supports for the platform. The slavecylinder keeps the platform level through theentire range of boom motion. It operates in aclosed-circuit hydraulic loop with the mastercylinder. The slave cylinder is equipped withcounterbalance valves to prevent movement inthe event of a hydraulic line failure.How to Remove the PlatformLeveling Slave CylinderNote: Before cylinder removal is considered, bleedthe slave cylinder to be sure there is no air in theclosed loop.Note: When removing a hose assembly or fitting,the O-ring (if equipped) on the fitting and/or thehose end must be replaced. All connections mustbe torqued to specification during installation.Refer to Section 2,Hydraulic Hose and FittingTorque Specifications.1 Extend the primary boom until the slave cylinderbarrel-end pivot pin is accessible.2 Raise the primary boom slightly and placeblocks under the platform for support.3 Lower the primary boom until the platform isresting on the blocks just enough to support theplatform.Note: Do not rest the entire weight of the boom onthe blocks.4 Remove the pin retaining fastener from theslave cylinder rod-end pivot pin. Use a softmetal drift to drive the rod-end pivot pin out.Crushing hazard. The jib boomcould fall when the slave cylinderrod-end pivot pin is removed if notproperly supported.5 Remove the external snap rings from the barrel-end pivot pin.6 Use a soft metal drift to drive the barrel-endpivot pin out.7 Carefully pull the cylinder out of the primaryboom to access the hydraulic hoses.8 Tag, disconnect and plug the hydraulic hosesfrom the slave cylinder. Cap the fittings on thecylinder.Bodily injury hazard. Sprayinghydraulic oil can penetrate andburn skin. Loosen hydraulicconnections very slowly to allowthe oil pressure to dissipategradually. Do not allow oil tosquirt or spray.How to Bleed the Slave CylinderNote: Do not start the engine. Use auxiliary powerfor this procedure.1 Raise the primary boom to a horizontal position.2 Move the platform level toggle switch up anddown through two platform leveling cycles toremove any air that might be in the system.
|
