Contents - Introduction
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Machine Specifications
- Performance Specifications
- Hydraulic Component Specifications
- Valve Coil Resistance Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Pre-Delivery Preparation
- Maintenance Inspection Report
- A-1 Inspect the Manuals and Decals
- A-2 Perform Pre-operation Inspection
- A-4 Perform Function Tests
- A-6 Check the High Pressure Hydraulic Filter Condition Indicator
- A-8 Perform Engine Maintenance - Deutz and Continental Models
- A-10 Grease the Turntable Rotation Bearing and Rotate Gear
- A-11 Perform Engine Maintenance
- A-12 Replace the Drive Hub Oil
- A-13 Perform Engine Maintenance - Perkins Models
- B-1 Inspect the Battery(s)
- B-2 Inspect the Electrical Wiring
- B-3 Test the Key Switch
- B-5 Inspect the Engine Air Filter
- B-6 Check the Oil Cooler and Cooling Fins - Deutz Models
- B-7 Confirm the Proper Brake Configuration
- B-10 Check and Adjust the Engine RPM
- B-11 Perform Engine Maintenance
- B-13 Test the Ground Control Override
- B-15 Test the Engine Idle Select Operation
- B-16 Test the Fuel Select Operation - Gasoline/LPG Models
- B-17 Test the Drive Enable System
- B-18 Test the Drive Brakes
- B-20 Test the Drive Speed - Raised or Extended Position
- B-21 Test the Alarm Package (if equipped) and the Descent Alarm
- B-22 Inspect the Fuel and Hydraulic Tank Cap Venting Systems
- B-23 Perform Hydraulic Oil Analysis
- C-2 Grease the Platform Overload Mechanism (if equipped)
- C-3 Test the Platform Overload System (if equipped)
- C-5 Replace the Fuel Filter/ Water Separator Element - Diesel Models
- C-6 Check the Safety Envelope Limit Switches and Angle Sensor, S-80X
- D-1 Check the Boom Wear Pads
- D-2 Check the Free-wheel Configuration
- D-3 Check the Turntable Rotation Bearing Bolts
- D-5 Perform Engine Maintenance
- D-7 Replace the Drive Hub Oil
- D-8 Perform Engine Maintenance - Deutz Models
- E-1 Test or Replace the Hydraulic Oil
- E-2 Perform Engine Maintenance - Perkins Models
- ALC-500 Circuit Board
- Joysticks
- Platform
- Platform Leveling Slave Cylinder
- Platform Rotator
- Calibrate the Platform Overload System
- Jib Boom Components,
- Function Manifold Components
- Valve Adjustments - Function Manifold
- Brake/Two-speed Manifold Components
- Turntable Rotation Manifold Components
- Platform Rotate Manifold Components
- Platform Manifold Components, S-80
- Platform Manifold Components, S-85
- WD Traction Manifold Components
- Drive Oil Diverter Manifold Components (welder option)
- Valve Adjustments - Traction Manifold
- Valve Coils
- Fuel Tank
- Hydraulic Tank
- Turntable Rotation Drive Hub Assembly
- Yoke and Hub
- Steer Cylinder
- Yoke and Drive Hub
- Drive Motor
- Steer Cylinders
- Oscillate Axle Cylinders
- Oscillate Directional Valve
- Fault Codes - Control System
- Electrical Symbols Legend
- Hydraulic Symbols Legend
- Connector Pin Legend - View 1
- Connector Pin Legend - View 2
- Deutz TD2011L04i Models
- Platform Control Box Wiring Diagram, S-80 and S-85 (ANSI / CSA / AS Deutz TD2011L04i Models
- Electrical Schematic, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Deutz TD2011L04i Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Electrical Schematic, S-80X Deutz TD2011L04i Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Deutz TD2011L04i Models
- Platform Control Box Wiring Diagram, S-80X Deutz TD2011L04i Models
- Electrical Schematic, S-80 and S-85 (ANSI / CSA / AS Perkins 804D-33 Models
- Perkins 804D-33 Models
- Electrical Schematic, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Perkins 804D-33 Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Electrical Schematic, S-80X Perkins 804D-33 Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Perkins 804D-33 Models
- Platform Control Box Wiring Diagram, S80X Perkins 804D-33 Models
- Platform Control Box Switch Panel Wiring Diagram, S80X Perkins 804D-33 Models
- Continental TME27 Models
- Ground Control Box Terminal Strip Wiring Diagram S-80 and S-85 (ANSI / CSA / AS), Continental TME27 Models
- Platform Control Box Wiring Diagram, S-80 and S-85 (ANSI / CSA / AS Continental TME27 Models
- Electrical Schematic, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Continental TME27 Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Electrical Schematic, S-80X Continental TME27 Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Continental TME27 Models
- Platform Control Box Wiring Diagram, S-80X Continental TME27 Models
- Continental TME27 Engine Harness
- Platform Level Cutout, CTE Option
- Continental Options Schematic
- Deutz and Perkins Options Schematic
- kW Hydraulic Generator Wiring Diagram
- kW Hydraulic Generator Electrical Schematic
- Belt Driven Generator Option
- Relay and Fuse Panel Legend
- Hydraulic Schematic, 2WD Models
- Hydraulic Schematic, 4WD Models
- kW Hydraulic Generator Hydraulic Schematic
|
Part No. 122985 S-80 • S-85 • S-80X 3 - 53Section 3 • Scheduled Maintenance ProceduresFebruary 2012CHECKLIST D PROCEDURESD-5Perform Engine MaintenanceEngine specifications require that this procedure beperformed every 1000 hours.Proper engine maintenance, following the enginemanufacturer's maintenance schedule, is essentialto good engine performance and service life. Failureto perform the maintenance procedures can lead topoor engine performance and component damage.Required maintenance procedures and additionalengine information are available in the:Deutz TD2011 Operation Manual(Deutz part number 0312 3547) OR thePerkins 804D-33 Operation and MaintenanceManual (Perkins part number SEBU7853-00) ORtheContinental TME27 Owner's Manual(Continental part number WM10303).Deutz TD2011 Operation ManualGenie part number 139320Perkins 804D-33 Operation and Maintenance ManualGenie part number 111332Continental TME27 Owner's ManualGenie part number 111901To access the engine:1 Remove the engine tray retaining fastenerlocated under the engine tray. Swing the enginetray out away from the machine and secure itfrom moving.Crushing hazard. Failure to installthe fastener into the engine trayanchor hole to secure the enginetray from moving could result indeath or serious injury.D-6Replace the Hydraulic FiltersNote: Genie requires that this procedure beperformed every 1000 hours or annually, whichevercomes first. Perform this procedure more often ifdusty conditions exist.Replacement of the hydraulic filters is essential forgood machine performance and service life. A dirtyor clogged filter may cause the machine to performpoorly and continued use may cause componentdamage. Extremely dirty conditions may requirethat the filters be replaced more often.Bodily injury hazard. Beware of hotoil. Contact with hot oil may causesevere burns.Note: Perform this procedure with the engine off.Hydraulic return filter:1 Open the ground controls side turntable coverand locate the hydraulic return filter housing ontop of the hydraulic tank.2 Remove the cap from the filter housing.3 Lift the handle on the filter element and rotatethe element counterclockwise to release theelement from the housing.4 Remove the filter element from the filterhousing.5 Install the new filter element into the filterhousing.6 Push the filter element down to be sure theO-ring on the element is fully seated into thehousing.7 Rotate the filter element clockwise to lock it inplace.
|
