Contents - Introduction
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Machine Specifications
- Performance Specifications
- Hydraulic Component Specifications
- Valve Coil Resistance Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Pre-Delivery Preparation
- Maintenance Inspection Report
- A-1 Inspect the Manuals and Decals
- A-2 Perform Pre-operation Inspection
- A-4 Perform Function Tests
- A-6 Check the High Pressure Hydraulic Filter Condition Indicator
- A-8 Perform Engine Maintenance - Deutz and Continental Models
- A-10 Grease the Turntable Rotation Bearing and Rotate Gear
- A-11 Perform Engine Maintenance
- A-12 Replace the Drive Hub Oil
- A-13 Perform Engine Maintenance - Perkins Models
- B-1 Inspect the Battery(s)
- B-2 Inspect the Electrical Wiring
- B-3 Test the Key Switch
- B-5 Inspect the Engine Air Filter
- B-6 Check the Oil Cooler and Cooling Fins - Deutz Models
- B-7 Confirm the Proper Brake Configuration
- B-10 Check and Adjust the Engine RPM
- B-11 Perform Engine Maintenance
- B-13 Test the Ground Control Override
- B-15 Test the Engine Idle Select Operation
- B-16 Test the Fuel Select Operation - Gasoline/LPG Models
- B-17 Test the Drive Enable System
- B-18 Test the Drive Brakes
- B-20 Test the Drive Speed - Raised or Extended Position
- B-21 Test the Alarm Package (if equipped) and the Descent Alarm
- B-22 Inspect the Fuel and Hydraulic Tank Cap Venting Systems
- B-23 Perform Hydraulic Oil Analysis
- C-2 Grease the Platform Overload Mechanism (if equipped)
- C-3 Test the Platform Overload System (if equipped)
- C-5 Replace the Fuel Filter/ Water Separator Element - Diesel Models
- C-6 Check the Safety Envelope Limit Switches and Angle Sensor, S-80X
- D-1 Check the Boom Wear Pads
- D-2 Check the Free-wheel Configuration
- D-3 Check the Turntable Rotation Bearing Bolts
- D-5 Perform Engine Maintenance
- D-7 Replace the Drive Hub Oil
- D-8 Perform Engine Maintenance - Deutz Models
- E-1 Test or Replace the Hydraulic Oil
- E-2 Perform Engine Maintenance - Perkins Models
- ALC-500 Circuit Board
- Joysticks
- Platform
- Platform Leveling Slave Cylinder
- Platform Rotator
- Calibrate the Platform Overload System
- Jib Boom Components,
- Function Manifold Components
- Valve Adjustments - Function Manifold
- Brake/Two-speed Manifold Components
- Turntable Rotation Manifold Components
- Platform Rotate Manifold Components
- Platform Manifold Components, S-80
- Platform Manifold Components, S-85
- WD Traction Manifold Components
- Drive Oil Diverter Manifold Components (welder option)
- Valve Adjustments - Traction Manifold
- Valve Coils
- Fuel Tank
- Hydraulic Tank
- Turntable Rotation Drive Hub Assembly
- Yoke and Hub
- Steer Cylinder
- Yoke and Drive Hub
- Drive Motor
- Steer Cylinders
- Oscillate Axle Cylinders
- Oscillate Directional Valve
- Fault Codes - Control System
- Electrical Symbols Legend
- Hydraulic Symbols Legend
- Connector Pin Legend - View 1
- Connector Pin Legend - View 2
- Deutz TD2011L04i Models
- Platform Control Box Wiring Diagram, S-80 and S-85 (ANSI / CSA / AS Deutz TD2011L04i Models
- Electrical Schematic, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Deutz TD2011L04i Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Deutz TD2011L04i Models (after serial number 8110)
- Electrical Schematic, S-80X Deutz TD2011L04i Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Deutz TD2011L04i Models
- Platform Control Box Wiring Diagram, S-80X Deutz TD2011L04i Models
- Electrical Schematic, S-80 and S-85 (ANSI / CSA / AS Perkins 804D-33 Models
- Perkins 804D-33 Models
- Electrical Schematic, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Perkins 804D-33 Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Perkins 804D-33 Models (after serial number 8110)
- Electrical Schematic, S-80X Perkins 804D-33 Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Perkins 804D-33 Models
- Platform Control Box Wiring Diagram, S80X Perkins 804D-33 Models
- Platform Control Box Switch Panel Wiring Diagram, S80X Perkins 804D-33 Models
- Continental TME27 Models
- Ground Control Box Terminal Strip Wiring Diagram S-80 and S-85 (ANSI / CSA / AS), Continental TME27 Models
- Platform Control Box Wiring Diagram, S-80 and S-85 (ANSI / CSA / AS Continental TME27 Models
- Electrical Schematic, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Platform Control Box Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (before serial number 8111)
- Electrical Schematic, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Ground Control Box Terminal Strip Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Ground Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Continental TME27 Models (after serial number 8110)
- Platform Control Box Switch Panel Wiring Diagram, S-80 and S-85 (CE Continental TME27 Models (after serial number 8110)
- Electrical Schematic, S-80X Continental TME27 Models
- Ground Control Box Terminal Strip Wiring Diagram, S-80X Continental TME27 Models
- Platform Control Box Wiring Diagram, S-80X Continental TME27 Models
- Continental TME27 Engine Harness
- Platform Level Cutout, CTE Option
- Continental Options Schematic
- Deutz and Perkins Options Schematic
- kW Hydraulic Generator Wiring Diagram
- kW Hydraulic Generator Electrical Schematic
- Belt Driven Generator Option
- Relay and Fuse Panel Legend
- Hydraulic Schematic, 2WD Models
- Hydraulic Schematic, 4WD Models
- kW Hydraulic Generator Hydraulic Schematic
|
3 - 54 S-80 • S-85 • S-80X Part No. 122985Section 3 • Scheduled Maintenance Procedures February 2012CHECKLIST D PROCEDURES8 Install the filter housing cap.9 Use a permanent ink marker to write the dateand number of hours from the hour meter on theoil filter housing.Medium and high pressure filters:Note: The medium pressure filter is for the chargepump and the high pressure filter is for all machinefunctions except the drive circuit and oscillatingaxle circuit.10 Open the engine side turntable cover and locatethe two filters.Note: The high pressure filter is located toward thebulkhead with a condition indicator. The mediumpressure filter is located nearest the operator.11 Place a suitable container under the filters.12 Remove the filter housing by using a wrench onthe nut provided on the bottom of the housings.13 Remove the filter element from the housings.14 Inspect the housing seals and replace them ifnecessary.15 Install the new medium and high pressure filterelements into the housings and tighten themsecurely.16 Clean up any oil that may have spilled during theinstallation procedure.17 Use a permanent ink marker to write the dateand number of hours from the hour meter on theoil filter housings.18 Start the engine from the ground controls.19 Inspect the filter housings and relatedcomponents to be sure that there are no leaks.D-7Replace the Drive Hub OilGenie specifications require that this procedure beperformed every 1000 hours or annually, whichevercomes first.Replacing the drive hub oil is essential for goodmachine performance and service life. Failure toreplace the drive hub oil at yearly intervals maycause the machine to perform poorly and continueduse may cause component damage.Drive hubs:1 Select the drive hub to be serviced. Drive themachine until one of the two plugs is at thelowest point.2 Remove both plugs and drain the oil into asuitable container.3 Drive the machine until one plug is at the topand the other is at 90 degrees.a. models with o-ring plugs4 Fill the hub with oil from the top hole until the oillevel is even with the bottom of the side plughole. Install the plugs.5 Install the plugs into the drive hub. Torque toSpecification. Refer to Section 2,Specifications.a
|
