Panasonic System 850 Operating Instructions Manual

Also see for System 850: Brochure

Contents

54@1 Alarm Reset button (RESET)Cancels an activated alarm.Press this button to reset an alarm activated in the cur-rently active unit.Pressing this button while holding down the SHIFT but-ton cancels all currently activated alarms at a time (ALLRESET).Pressing RESET in the Camera Menu will reset theparameter of a selected item or open the SpecialCamera Menu when the cursor is positioned on SPE-CIAL in the menu. Pressing it while holding down theSHIFT button will restore all factory default settings.@2 Next button (NEXT)This button is used to move a Tour Sequence one stepforward from the step that was previously paused onthe active monitor by pressing the PAUSE button.The button is also used to select a camera. PressingNEXT while holding down the CAMERA (ENTER) buttonwill replace the currently selected camera with the nexthigher camera number, if the active monitor is in Spotmode.Similarly pressing NEXT while holding down the MONI-TOR button will select the next higher monitor number.When selecting alarms, pressing NEXT while holdingdown the ALARM button will select the next alarm.@3 Previous button (PREV)This button is used to move a Tour Sequence one stepbackward from the step that was previously paused onthe active monitor by pressing the PAUSE button.This button is also used to select a camera. PressingPREV while holding down the CAMERA (ENTER) buttonwill replace the currently selected camera with the nextlower camera number, if the active monitor is in Spotmode.Similarly pressing PREV while holding down the MONI-TOR button will select the next lower monitor number.When selecting alarms, pressing PREV while holdingdown the ALARM button will select the previous alarm.Pressing this button while holding down the SHIFT but-ton will display the Controller ID number on the LEDDisplay for about 3 seconds (S-CTL ID).@4 Stop button (STOP)This button is used to end a Tour Sequence that isbeing run on the active monitor.To end a Group sequence, select one of the monitorsthat are being run on the selected sequence, thenpress this button.Pressing STOP while holding down the SHIFT buttonwill open the Camera Menu on the active monitor. TheSTOP indicator will light. (CAM MENU ON)@5 Pause button (PAUSE)This button is used to pause a Tour or Group Sequencethat is being run on the active monitor.Pressing PAUSE while holding down the SHIFT buttonwill close the Camera Menu on the active monitor. TheSTOP indicator will go off. (CAM MENU OFF)@6 Tour Sequence button (TOUR SEQ)This button, in combination with the Numeric buttons, isused to run a Tour Sequence on the active monitor.Pressing TOUR SEQ will restart a forward sequencefrom the next step that was previously paused bypressing the PAUSE button.@7 Group Sequence button (GROUP SEQ)This button, in combination with the Numeric buttons, isused to run a Group Sequence on the assigned moni-tors.Pressing GROUP SEQ will restart a forward sequencefrom the next step that was previously paused bypressing the PAUSE button.@8 Group Preset button (GROUP PRESET)This button, in combination with the Numeric buttons, isused to activate a previously programmed GroupPreset function.Pressing This button while holding down the SHIFT but-ton will display the Operator ID number on the LEDDisplay for about 3 seconds (OPE ID).@9 Log Out button (LOGOUT)This button, in combination with the CAMERA (ENTER)button, is used to log out from the system.To prevent a log-out error, press CAMERA (ENTER)while holding down the LOGOUT button.#0 Function buttons (F1, F2)These buttons provide access to camera attributes andoperating functions.F1: Reserved for future use.F2: Pressing this button will select the mode for control-ling selected camera function (CAM FUNC).#1 OSD (On-Screen Display) button (OSD)This button is used to toggle the currently selected dis-play on and off on the active monitor.Pressing the numeric buttons shown below while hold-ing down the OSD button will toggle the following dis-play items on the active monitor on and off.1: Clock Display (T&D)2: Camera Title Display (CAM ID)3: General Status Display (GEN)5: Monitor Status Display (MON STATUS)6: All Displays except clock (ALL)#2 Monitor button (MONITOR)This button is used to select a monitor.To select a monitor, press the corresponding Numericbuttons, followed by the MONITOR button.Pressing this button while holding down the SHIFT but-ton will toggle the indicator on and off. The indicatorlights to indicate that the currently selected monitor ispriority locked, and retains control of a monitor by anoperator.This button, in combination with the Numeric buttons, isalso used to display the status and history tables on theactive monitor screen.