Denon AVR-4810 Owner's Manual

Also see for AVR-4810: Service manual

Contents

Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsSettingsENGLISHAudyssey Auto Setup detects the presence of each speaker andautomatically calculates the speaker size, channel level, distance andcrossover frequency settings. In addition, acoustical distortions arecorrected within the listening area.When measuring begins, a test tone is output from each speaker.Position and connect all speakers before commencing AudysseyAuto Setup.•••STEP2 Speaker Detection1 Select “Measure” andthen press ENTER.AUDYSSEY AUTO SETUP1 2 3 4 5 6RETURNMeasureSTEP2 Speaker DetectionPlease place the microphone at earheight at main listening position.Start measurement. Output large test tone during measuringEnter Cancelq Measure the subwooferlevelTo stop measuring, select“Cancel” and then pressENTER.bWhen “Subwoofer” is set to “Skip” with “Channel Skip”, thismeasurement is not taken, and the process proceeds to “wMeasure each speaker”.w Measure each speakerOnce the measurements in step q are complete, themeasurements in step w start automatically.The measuring channel changes depending on the setting of “AmpAssign” (vpage 38 ~ 40) and “Channel Skip” (vpage 33).When an error message is displayed, check “Error Messages” fordetails (vpage 36).e Check the speaker detection resultsWhen measuring ends, the speaker detection results aredisplayed.Select “Next → Measurement” and press ENTER to proceed to“ STEP3 ”.Press u to select “Retry”, and when you press ENTER, measuringat the main listening position starts again.bbbbbd Perform Audyssey Auto SetupMake the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup)STEP3 Measurement2 Move the setupmicrophone toposition 2, select“Measure”, and thenpress ENTER.The measurement of the2nd position starts.AUDYSSEY AUTO SETUP1 2 3 4 5 6RETURNMeasureSTEP3 MeasurementPlease place the microphone at earheight at 2nd listening position.Start measurement. Output large test tone during measuringEnter CancelNext CalculationTo skip this step, select “Next → Calculation” and proceed toSTEP4 .b3 Repeat step 2,measuring positions3 ~ 8.When measurement ofposition 8 is completed,a “Measurementsfinished.” message isdisplayed.AUDYSSEY AUTO SETUP1 2 3 4 5 6RETURNSTEP3 MeasurementPlease place the microphone at earheight at 3rd listening position.Start measurement. Output large test tone during measuringEnter CancelNext CalculationMeasureRetryTo skip this step, select “Next → Calculation” and proceed toSTEP4 .Measure in at least 6 positions in and around the main listeningposition. Even though you can complete measurement with atleast 6 positions, it is advisable to use more than 6 (a maximumof 8 positions).bbSTEP4 Calculation4 On the STEP3screen, select “Next→ Calculation”, andthen press ENTER.Measuring resultsare analyzed, and thefrequency responseof each speaker inthe listening room isdetermined.AUDYSSEY AUTO SETUP1 2 3 4 5 6STEP4 CalculationNow calculating... Please wait.50%Analysis takes several minutes to complete. The time required forthis analysis depends on the number of speakers connected.The more connected speakers there are, the longer it takes toperform analysis.bSTEP5 Check5 On the STEP5screen, press uito select the item youwant to check, andthen press ENTER.Speaker Config. CheckDistance CheckChannel Level CheckCrossover Freq. CheckAUDYSSEY AUTO SETUP1 2 3 4 5 6RETURNSTEP5 CheckCheck processing results.To proceed, press “Next”.Select item to checkEnter CancelNext StoreCh. Level CheckCrossover CheckDistance CheckSpkr Config CheckSubwoofers may measure a greater reported distance thanthe actual distance due to added electrical delay common insubwoofers.b6 Press ui to select the channel you want to check.The measurement result of each speaker is displayed.If you want to check another item, press RETURN.Select “Next → Store” and press ENTER to proceed to “ STEP6 ”.bbMain remote control unitoperation buttons:Displaying the menuCancel the menu:Moves the cursor(Up/Down/Left/Right) :Confirm the setting :Return to previous menu