Denon AVR-4810 Owner's Manual

Also see for AVR-4810: Service manual

Contents

Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsSettingsENGLISH3 Adjust the volumecontrol on yoursubwoofer so thatthe measured level iswithin the 72 ~ 78 dBrange.AUDYSSEY AUTO SETUP1 2 3 4 5 673.9dBStopSubwoofer Level MatchingPlease adjust the level of your active subwoofer unitso that the level Indicates approx. 75dBChange from red to blue when level matchesEnterIf the measured level is within the 72 ~ 78 dB range, the levelindicator is blue.b4 When the measured level is within the 72 ~ 78 dBrange, press ENTER.5 Select “Next” andthen press ENTER.Proceed to “d:PerformAudyssey Auto Setup,STEP2 : SpeakerDetection” (vpage 34),1 - w.AUDYSSEY AUTO SETUP1 2 3 4 5 6RETURNSW Test Start73.8dBNextSubwoofer Level MatchingAfter adjustment, push “Next”.Proceed to next measurementEnter CancelMake the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup)Main remote control unitoperation buttons:Displaying the menuCancel the menu:Moves the cursor(Up/Down/Left/Right) :Confirm the setting :Return to previous menuSubwoofer Level Error Message and How to AdjustThe optimal level of the subwoofer channel is 75 dB. During subwoofer level measurement (d:Perform Audyssey Auto Setup, “ STEP2 :Speaker Detection” (vpage 34), 1 - q), an error message is displayed when the subwoofer level is outside the 72 ~ 78 dB range. When usinga subwoofer with built-in amplifier (active type), adjust the subwoofer volume so that the subwoofer level is within the 72 ~ 78 dB range.1 Select “SW LevelMatching” and thenpress ENTER.AUDYSSEY AUTO SETUP1 2 3 4 5 6RETURNThe subwoofer’s level is too high or low. Please select “SWLevel Matching” and adjust the level of your subwoofer unit.If you do not want to use thesubwoofer, select “Skip”.Proceed to subwoofer volume adjustment itemEnter CancelSkipCaution!SW Level Matching2 Select “SW TestStart” and then pressENTER.Subwoofer levelmeasurement begins.During measuring, a“Testing …” message isdisplayed.The measured levelappears on the levelindicator after about 3 ~5 seconds.AUDYSSEY AUTO SETUP1 2 3 4 5 6RETURNNextdBSW Test StartSubwoofer Level MatchingPlease place the microphone at ear height at mainlistening position, then push ENTER.Start measurement Output large test tone from subwooferEnter CancelAUDYSSEY AUTO SETUP1 2 3 4 5 679.1dBStopSubwoofer Level MatchingPlease adjust the level of your active subwoofer unitso that the level Indicates approx. 75dBChange from red to blue when level matchesEnterIf the measured level is outside the 72 ~ 78 dB range, the levelindicator is red.When measuring stops, press ENTER.bbRedBlueThis is displayed after Audyssey Auto Setup is completed.If you set “Restore” to “Yes”, you can return to Audyssey Auto Setupmeasurement result (value calculated at the start by MultEQ XT) evenwhen you have changed each setting manually.Check the Measuring Results andEqualizer Type after Audyssey AutoSetup (Parameter Check)1 Press i to select“Parameter Check”,and then pressENTER or p.PARAMETER CHECKSpkr Config CheckDistance CheckCh. Level CheckCrossover CheckEQ CheckRestoreCheck auto setup measurement results2 Press ui to select the item you want to check, andthen press ENTER or p.Speaker Config. Check Distance Check Channel Level CheckCrossover Freq. Check EQ Check3 Press ui to select the channel you want to check.The measurement result of each speaker is displayed.When you selected “EQ Check” in step 2, press ui to select theCorrection curve you want to check (“Audyssey” or “AudysseyFlat”).When you want to check another item, press RETURN.Pressing RETURN returns you to step 2; from there, proceed tosteps 2 and 3.bb