Denon AVR-4810 Owner's Manual

Also see for AVR-4810: Service manual

Contents

Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsSettingsENGLISHMaking Detailed Settings (Manual Setup)Setting items Setting contentsRemote IDSet when you operateanother DENON AV amplifierwith the remote control unitof the AVR-4810. Match theremote control unit you areusing with the remote ID ofthe AVR-4810.1 / 2 / 3 / 4When changing the remote ID, also change the “MAIN”, “iPod”,“TUNER” and “NET/USB” modes of the main remote control unit atthe same time. Also change the sub remote control unit at the sametime (vpage 104, 109 “Setting the Remote ID”).232C PortSet when using an externalcontroller or two-way remotecontrol unit connected to theRS-232C terminal.Serial Control : Set when using an external controller.2Way Remote : Set when using a 2-way remote control unit.When using a DENON two-way remote control unit (RC-7000CI or RC-7001RCI, sold separately), set to “2Way Remote”.NOTEWhen setting to “2Way Remote”, you can not use the RS-232C connectoras an external controller.DimmerAdjust display brightness ofthe receiver.Bright : Normal display brightness.Dim : Reduced display brightness.Dark : Very low display brightness.OFF : Turns the display off.Setup LockProtect settings frominadvertent change.OFF : Turn protection off.ON : Turn protection on.When “Setup Lock” is set to “ON”, the settings listed below can nolonger be changed. Also, “SETUP LOCKED!” is displayed if you attemptto operate related settings.· GUI menu operations · Dynamic Volume· RESTORER · Channel Level· Audio/Video Adjust · Audio Delay· MultEQ XT · Input Mode· Dynamic EQWhen canceling the setting, set “Setup Lock” to “OFF”.••Maintenance ModeUsed when receivingmaintenance from a DENONservice engineer or custominstaller.NOTEOnly use this function if so instructed by a DENON serviceperson orinstaller.Main remote control unitoperation buttons:Displaying the menuCancel the menu:Moves the cursor(Up/Down/Left/Right) :Confirm the setting :Return to previous menuSetting items Setting contentsFirmware UpdateUpdate the firmware of thereceiver.Check for Update : You can check for firmware updates. You can alsocheck approximately how long it will take to complete an update.Start : Execute the update process.When updating starts, the power indicator becomes red and the GUIscreen is shut down. The amount of update time which has elapsed isdisplayed.When updating is complete the power indicator becomes green andnormal status is resumed.If updating fails, the set automatically retries, but if updating is still notpossible, one of the messages shown below is displayed. If the displayreads as shown below, check the settings and network environment,then update again.Display DescriptionUpdating failed Updating failed.Login failed Failure to log into server.Server is busy Server is busy. Wait a while then try again.Connection fail Failure connecting to server.Download fail Downloading of the firmware has failed.bAdd New FeatureDisplay new features thatcan be downloaded to theAVR-4810 and perform anupdate.Upgrade : Execute the upgrade process.When updating starts, the power indicator becomes red and the GUIscreen is shut down. The amount of update time which has elapsed isdisplayed.When upgrading is complete the power indicator becomes green andnormal status is resumed.If the upgrade is not successful, an error message identical to those in“Firmware Update” will appear on the display, check the settings andnetwork environment, then update again.bUpgrade Status : A list of the additional functions provided by the Upgradewill be displayed.See the DENON website for details about updates.When the procedure is complete, “Registered” is displayed in thismenu and updates can be carried out. If the procedure has not beencarried out, “Not Registered” is displayed.The ID number shown on this screen is needed when carrying out theprocedure.The ID number can also be displayed by pressing and holding p andSTATUS on the main unit for at least 3 seconds.See overleaf