Denon AVR-4810 Owner's Manual

Also see for AVR-4810: Service manual

Contents

Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsSettingsENGLISHMaking Detailed Settings (Manual Setup)Main remote control unitoperation buttons:Displaying the menuCancel the menu:Moves the cursor(Up/Down/Left/Right) :Confirm the setting :Return to previous menuSetting items Setting contentsNetwork Connecting(Continued)y Use i to select “Connection” and press ENTER.Network connection starts.When connection is established with the access point, “Connectioncompleted.” is displayed.ExitNETWORK CONNECTINGDetailTerminate setupConnection completed.DHCP192.168.100.85IP AddressEnterONAVR-4810 performs automatic network setup due to the DHCPfunction.When connecting to a network without a DHCP function, you will needto manually configure the IP address.For details, see page 48 “Wired LAN settings” in step 3.Wired LAN settingsUse this procedure to configure the Wired LAN settings.1. Connect the LAN cable (vpage 25 “Connecting to a Home Network(LAN)”).2. Turn on the AVR-4810 (vpage 27 “Turning the Power On”).AVR-4810 performs automatic network setup due to the DHCPfunction.When connecting to a network that has no DHCP function, perform thesetting in step 3.3. Set the IP address at the “Network Connecting”.NETWORK CONNECTINGExitDetail192.168.100.33Set IP address and proxy manuallyONDHCPIP AddressEnterNETWORK CONNECTINGProxyExit192 . 168 . 100 . 033Set IP address manuallyOFFDHCPIP Address255 . 255 . 255 . 000Subnet Mask000 . 000 . 000 . 000Default Gateway000 . 000 . 000 . 000Primary DNS000 . 000 . 000 . 000Secondary DNSRETURN Cancelqwr eSetting items Setting contentsNetwork Connecting(Continued)q On the GUI menu, select “Network Connecting” – “Detail” andpress ENTER.w Use o p to set “DHCP” to “OFF”, then press i.The DHCP function is disabled.e Use uip to input the address and press ENTER.IP Address : Set the IP address within the ranges shown below.The Network Audio function cannot be used if other IP addressesare set.CLASS A: 10.0.0.0 ~ 10.255.255.255CLASS B: 172.16.0.0 ~ 172.31.255.255CLASS C: 192.168.0.0 ~ 192.168.255.255Subnet Mask : When connecting an xDSL modem or terminaladapter directly to the AVR-4810, input the subnet mask indicatedin the documentation supplied by your provider. Normally input255.255.255.0.Default Gateway : When connected to a gateway (router), inputits IP address.Primary DNS, Secondary DNS : If there is only one DNS addressindicated in the documentation supplied by your provider, input itat “Primary DNS”. If there are two or more DNS addresses, inputthe first one at “Secondary DNS”.r Use i to select “Exit” and press ENTER.Setup is complete.When connecting to the network via a Proxy server, select “Proxy” andpress ENTER (vpage 49 “Proxy settings”).If you are using a broadband router (DHCP function), there is no needto make the settings at “IP Address” and “Proxy”, since the DHCPfunction is set to “ON” in the AVR-4810’s default settings.If the AVR-4810 is being used connected to a network without theDHCP function, the network settings must be made. In this case, someknowledge of networks is required. For details, consult a networkadministrator.If you cannot connect to the Internet, recheck the connections andsettings (vpage 25).If you do not understand about Internet connection, contact your ISP(Internet Service Provider) or the store from which you purchased yourcomputer.When you want to cancel the setting during IP address input, pressRETURN.••••b•••••