Denon AVR-4810 Owner's Manual

Also see for AVR-4810: Service manual

Contents

Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsSettingsENGLISHMaking Detailed Settings (Manual Setup)Main remote control unitoperation buttons:Displaying the menuCancel the menu:Moves the cursor(Up/Down/Left/Right) :Confirm the setting :Return to previous menuSetting items Setting contentsChannel Level(Continued)Default : Reset all distance settings to factory default.Yes : Reset to the defaults.No : Do not reset to the defaults.••Crossover FrequencyOutputs at below setfrequency, each speaker’sbass signal output fromthe subwoofer. Set thisaccording to the lowfrequency reproductioncapabilities of the speakersyou are using.40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /250Hz : Set the crossover frequency.Advanced : Specify crossover frequency for each speaker.Front / Center / Surround / Surround Back / Front Height / FrontWide : Select the speaker.40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz /250Hz : Set the crossover frequency.Can be set when the “Speaker Configuration” – “Subwoofer” (vpage40) setting is “Yes”, or when you have a speaker that is set to “Small”.Always set the crossover frequency to “80Hz”. When using smallspeakers, however, we recommend setting the crossover frequency toa higher frequency.For speakers set to “Small”, sound below the crossover frequency is cutfrom the sound output. The cut bass sound is output from the subwooferor front speakers.The speakers that can be set when “Advanced” is selected differaccording to the “Subwoofer Mode” setting (vpage 41).When “LFE” is selected, speakers set to “Small” at “SpeakerConfiguration” can be set. If the speakers are set to “Large”, “FullBand” is displayed and the setting cannot be made.If set to “LFE+Main”, this setting can be made regardless of thespeaker size.••••••••Speaker ImpedanceSet the impedance ofconnected speakers.8Ω/ohms : Select when the impedance of the connected speaker is 8Ω/ohms or more.6Ω/ohms : Select when the impedance of the connected speaker is atleast 6 Ω/ohms but less than 8 Ω/ohms.Check the speaker impedance (Ω) shown on the back of your speakersor in the instruction manual beforehand.Setting items Setting contentsRGB RangeSet the video range of RGBoutput from the HDMIterminal.Normal : Output with RGB video range (16 (black) to 235 (white)).Enhanced : Output with RGB video range (0 (black) to 255 (white)).This setting is valid when using a TV equipped with a DVI terminal.Vertical StretchExpand image signal invertical direction.ON : Expand image signal in vertical direction.OFF : Do not expand signal in vertical direction.This setting is valid with respect to the HDMI output when using anHDMI-compatible TV. When not using an HDMI-compatible TV, it isvalid with respect to the analog output.Auto Lip SyncAutomatic compensationfor timing shift in audio andvideo output.ON : Compensated.OFF : Not compensated.HDMI Audio OutSelect HDMI audio outputdevice.Amp : Playback through speakers connected to the receiver.TV : Playback through TV connected to the receiver.When the HDMI control function is operating, the setting of audioplayback in the connected TV takes priority (vpage 90 “HDMIControl Function”).Monitor OutMake settings for HDMImonitor output.Auto (Dual) : The presence of a TV connected to the MONITOR 1 orMONITOR 2 terminal is detected automatically, and that TV connectionis used.Monitor 1 : A TV connected to the MONITOR 1 terminal is always used.Monitor 2 : A TV connected to the MONITOR 2 terminal is always used.If both the Monitor 1 and 2 connectors are connected and “Resolution”(vpage 60) is set to “Auto”, the signals are output with a resolutioncompatible with both TV.With “Resolution” (vpage 60) not set to “Auto”, check whetherthe TV you are using is compatible with the resolution under “HDMIInformation” – “Monitor 1” and “Monitor 2” (vpage 87).Depending on the monitor you have connected, the display may not becorrect when you set to “Auto (Dual)”. In such a case, set to either“Monitor 1” or “Monitor 2”.You can also set “Monitor Out” by pressing M.SEL on the main remotecontrol unit.••••Make settings for HDMI video/audio output.Making the HDMI Settings (HDMI Setup)Default settings are underlined.