Denon AVR-4810 Owner's Manual

Also see for AVR-4810: Service manual

Contents

Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsSettingsENGLISHMaking Detailed Settings (Manual Setup)Main remote control unitoperation buttons:Displaying the menuCancel the menu:Moves the cursor(Up/Down/Left/Right) :Confirm the setting :Return to previous menuSetting items Setting contentsRemote Preset Codes(Continued)5. The procedures for registering remote control codes and remotecontrol preset registration are displayed.REMOTE PRESET CODESCategoryEnter preset codes using remote controllerDVDBrand HitachiCode 30573 30664 30695 3014130713 30884 307481. Press [DEVICE] button on the remote for preset registration2. Press and hold [RC SETUP] for at least 3 seconds3 . Using buttons [0-9], enter the 5-digit codeRETURN ReturnOPTIONb When there are several pages of preset codes, the pages can beswitched by pressing the main remote control unit’s o or p whenthe main remote control unit is in “MAIN” mode.How to carry out preset registerSee page 109 for details on how to carry out preset registration.1. Press DEVICE (DVD/HDP, VCR/DVR, TV or SAT/CABLE) on the mainremote control unit for the device you want to preset.2. Press and hold in RC SETUP on the main remote control unit for at least3 seconds.The signal transmission indicator flashes twice.3. Enter a 5-digit code using 0 ~ 9 on the main remote control unit.When the code is registered, the signal transmission indicator flashestwice.4. Check if the device is operating with the registered preset code.If the device does not operate try registering a different preset code.5. Press MAIN on the main remote control unit to set the remote controlto “MAIN” mode. Press MENU.The main unit can also be operated with MENU, uio p, ENTER.nQuick Select NameChange the “Quick Select”display title to one youprefer.1. Use ui to select the name of the Quick Select setting you want tochange, then press p or ENTER.2. Use o p to set the cursor to the character you want to change.3. Use ui to change the character, then press ENTER.Up to 16 characters can be input.You can change the character type when you press SEARCH on themain remote control unit or MENU during character input.The types of characters that can be input are as shown below.GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZGLower case charactersH abcdefghijklmnopqrstuvwxyzGSymbolsH ! # % & ‘ ( ) * + , - . / : ; < = “ > ? @ [ \ ]GNumbersH 0123456789 (Space)•••Setting items Setting contentsQuick Select Name(Continued)4. Repeat steps 1 ~ 3 to change the display name.Zone RenameChange the display title ofeach zone to one you prefer.1. Use ui to select the zone name (MAIN ZONE, ZONE2, ZONE3 orZONE4) you want to change, then press p or ENTER.2. Use o p to set the cursor to the character you want to change.3. Use ui to change the character, then press ENTER.Up to 10 characters can be input.You can change the character type when you press SEARCH on themain remote control unit or MENU during character input.The types of characters that can be input are as shown below.GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZGLower case charactersH abcdefghijklmnopqrstuvwxyzGSymbolsH ! # % & ‘ ( ) * + , - . / : ; < = “ > ? @ [ \ ]GNumbersH 0123456789 (Space)4. Repeat steps 1 ~ 3 to change the display name.•••Trigger Out 1Select the condition foractivating Trigger Out 1 forthe input source, surroundmode, etc.See “TRIGGER OUT jacks”(vpage 26) for moreinformation on trigger out.When Setting for Zone (MAIN ZONE / ZONE2 / ZONE3 / ZONE4)Trigger out is activated through linkage to the power of the zone set to“ON”.When Setting for Input SourceActivate trigger out when the input source set to “ON” is selected.Valid for the zone set to “ON” with “When Setting for Zone”.When Setting for Surround ModeActivate trigger out when the surround mode set to “ON” is selected.Valid when the “MAIN ZONE” set to “ON” with “When Settingfor Zone” is selected, and when the input source set to “ON” with“When Setting for Input Source” is selected.When Setting for HDMI MonitorActivate trigger out when the HDMI monitor set to “ON” is selected.Valid when the “MAIN ZONE” set to “ON” with “When Settingfor Zone” is selected, and when the input source set to “ON” with“When Setting for Input Source” is selected.When setting for “Vertical Stretch”Activate trigger out through linkage when “Vertical Stretch” (vpage42) is set to “ON”.ON : Activate trigger on this mode.– – – : Do not activate trigger on this mode.nnnnn••Trigger Out 2As with “Trigger Out 1”,select the condition foractivating Trigger Out 2.