Kenwood TKR-750 Programming Reference Manual

Also see for TKR-750: Brochure & specs Service manual Service manual Function reference Service manual

Version: 1.01 Field Programming Reference (FPRG) 346 EDIT MENU6.4.3 Others Tab (Optional Features)On this tab, you can activate/deactivate Power SaverMode and switch the power source, and configure thefunctions activating when the TKR-750/850/751/851 isturned ON.You can configure the Save On/Off, the Start Upoperation, the “Backup Power Function”, and the “MainPower Function”.Figure 6-11 Others tabTable 6-2 Available functionsFunction Name DescriptionNone The TKR-750/850/751/851 does not perform any operation.AUX Out 1 Off-AUX Out 5 OffThe function assigned to the specified Auxiliary Output port is disabled when the TKR-750/850/751/851 startsoperation. You can assign this function when “Selectable” is configure to the Auxiliary Output ports 1 - 5.(Refer to Table 6-7 Assigning Functions to the Auxiliary Output Ports.)AUX I/O 1 Off-AUX I/O 6 OffThe function assigned to the specified Auxiliary I/O port is disabled when the TKR-750/850/751/851 startsoperation. You can assign the function when “Selectable” is configured to the Auxiliary I/O ports 1 - 6.(Refer to Table 6-7 Assigning Functions to the Auxiliary Output Ports.)AUX Out 1 On-AUX Out 5 OnThe function assigned to the specified Auxiliary Output port is enabled when the TKR-750/850/751/851 startsoperation. You can assign this function when “Selectable” is configure to the Auxiliary Output ports 1 - 5.(Refer to Table 6-7 Assigning Functions to the Auxiliary Output Ports.)AUX I/O 1 On-AUX I/O 6 OnThe function assigned to the specified Auxiliary I/O port is enabled when the TKR-750/850/751/851 starts operation.You can assign the function when “Selectable” is configured to the Auxiliary I/O ports 1 - 6.(Refer to Table 6-7 Assigning Functions to the Auxiliary Output Ports.)Channel 1-Channel 16The TKR-750/850/751/851 moves to the channel selected from CH 1 to CH 16.You cannot configure this function when “Channel Select” is configured to Auxiliary I/O ports 1 - 4. “E2” appears onthe display when specifying the channel without data.(Refer to Table 6-7 Assigning Functions to the Auxiliary Output Ports.)Channel Down The TKR-750/850/751/851 moves to the next lower channel.The channel without data is skipped.Channel Up The TKR-750/850/751/851 moves to the next higher channel.The channel without data is skipped.CW ID On The TKR-750/850/751/851 sends the CW ID when it starts operation. (Refer to 6.3 CW ID Window.)This function is available on the channel having the CW ID.CW Message 1-CW Message 8The TKR-750/850/751/851 sends the assigned CW ID from CW Messages 1 to 8 when it starts operation. (Refer to6.12 CW Message Window.)DC Power SaveOffThe TKR-750/850/751/851 exits Power Saver Mode when it starts operation. You cannot configure this function tothe Save On/Off function.DC Power SaveOnThe TKR-750/850/751/851 enters Power Saver Mode when it starts operation. You cannot configure this function tothe Save On/Off function.Display Off All LEDs other than the Power SW LED that is located on the front panel unlit.This function can be enabled only when the TKR-750/850/751/851 is in Power Saver Mode.Display On All LEDs on the front panel light.This function can be enabled only when the TKR-750/850/751/851 is in Power Saver Mode.Hold TimeDisableThe TKR-750/850/751/851 disables the Repeat Hold Time.You can configure this function only when at least one channel is configured as the Repeat for Operation mode andthe Repeat Hold Time is enabled. (Refer to 6.4.1 Optional Features 1 Tab.)