- 276 -9. Operating Management/ Specifications• Printer Adjust• Print Position Adjust• Drum CleaningTrapping OFF Set trappingWidth / Length 210 mm (8.3inch) or216 mm (8.5inch)Sets the width of a custom paper size.Available range: 64 to 216 mm (2.5 to 8.5 inches)297 mm (11.7inch) or279 mm (11inch)Sets the length of a custom paper size.Available range: 90 to 1,321 mm (3.5 to 52.0 inches)Item FactorydefaultsettingDescriptionManual Timeout 60 seconds Sets for how many seconds the machine waits for paper to befed before cancelling a job when using the manual feeder.Timeout Injob 40 seconds Sets a time interval from when the machine stops receivingdata to when it starts a forced printing.Timeout Local 40 seconds Sets how long each port is left opened after a job is complete.(The network is excluded.)Timeout Network 90 seconds Sets how long the network port is left opened after a job iscomplete.Print Mode Without Color Toner Alarm Sets whether to print the document in black and white or stopwith alarm when a color toner empty error occurs.Jam Recovery Enable Sets whether to print the pages again that are not printed dueto a paper jam after the jam is cleared.Paper Black Setting 0 Adjusts finely if the black contrast becomes weak or blots orlines become conspicuous when printing on plain paper.If fine blots or lines appear, decrease the value. If the dark partbecomes light, increase the value.Paper Color Setting 0 Adjusts finely if the color contrast becomes weak, or blots orlines become conspicuous when printing on plain paper.If fine blots or lines appear, decrease the value. If the dark partbecomes light, increase the value.SMR Setting Black 0 Corrects variations in print results caused by temperature andhumidity conditions and differences in print density andfrequency. Change the setting if the print quality is uneven.Yellow 0Magenta 0Cyan 0Item FactorydefaultsettingDescriptionBG Setting Black 0 Corrects variations in print results caused by temperature andhumidity conditions and differences in print density andfrequency. Change the setting if the background is dark.Yellow 0Magenta 0Cyan 0HU Setting OFF Sets the mode to remove stain generated while being left for along time.VL Cleaning - Cleans the image drum.Set this mode when vertical white lines appear on the output.Gloss Mode OFF Raises the fusing temperature and prints highly glossy images.Set to [ON] when printing highly glossy images.Item FactorydefaultsettingDescriptionTray 1 X Adjust 0 mm • X Adjust: Adjusts the position of the entire printing imageperpendicular to the direction of paper movement.Available range: ±2.00 mm (0.25 mm increments).• Y Adjust: Adjusts the position of the entire printing imageparallel to the direction of paper movement.Available range: ±2.00 mm (0.25 mm increments).• Duplex X Adjust: Adjusts the position of the image on theback side of a duplex print perpendicular to the direction ofpaper movement.Available range: ±2.00 mm (0.25 mm increments).• Duplex Y Adjust: Adjusts the position of the image on theback side of a duplex print parallel to the direction of papermovement.Available range: ±2.00 mm (0.25 mm increments).Y Adjust 0 mmDuplex X Adjust 0 mmDuplex Y Adjust 0 mmTray 2/3(Optional)X Adjust 0 mmY Adjust 0 mmDuplex X Adjust 0 mmDuplex Y Adjust 0 mmMP Tray X Adjust 0 mmY Adjust 0 mmDuplex X Adjust 0 mmDuplex Y Adjust 0 mmItem FactorydefaultsettingDescriptionDrum Cleaning OFF Sets whether to clean the drum before printing. The imagequality improvement may be expected.Item FactorydefaultsettingDescription
