YASKAWA SI-EP3 Technical Manual

Also see for SI-EP3: Technical manual Technical manual Installation manual Installation manual

8 CommunicationYASKAWA SIEP C730600 89E PROFINET Technical Manual 43Drive Alarm Code(Hex.) *1 Description Drive Alarm Code(Hex.) *1 Description0406 Overtorque 2 (oL4) 042B PG Disconnected (PGo)0407 Rum Command Input Error (EF) 0431 Option Watchdog Error (E5)0408 Drive Baseblock (bb) 0432 Option Station Address Setting Error (AEr)0409 External Fault 3, input terminal S3 (EF3) 0433 Option Comm. Cycle Setting Error (CyC)040A External Fault 4, input terminal S4 (EF4) 0434 High Current Alarm (HCA)040B External Fault 5, input terminal S5 (EF5) 0435 Cooling Fan Maintenance Time (LT-1)040C External Fault 6, input terminal S6 (EF6) 0436 Capacitor Maintenance Time (LT-2)040D External Fault 7, input terminal S7 (EF7) 0438 Option EEPROM Error (EEP)040E External Fault 8, input terminal S8 (EF8) 0439 External Fault 1, (input terminal S1) (EF1)040F Cooling Fan Error (FAn) 043A External Fault 2, (input terminal S2) (EF2)0410 Overspeed (oS) 043B Safe Disable Input (HbbF)0411 Excessive Speed Deviation (dEv) 043C Safe Disable Input (Hbb)0412 PG Disconnected (PGo) 043D Mechanical Weakening Detection 1 (oL5)0414 MEMOBUS/Modbus Comm. Error (CE) 043E Mechanical Weakening Detection 2 (UL5)0415 Option Communication Error (bUS) 043F PLC Alarm (PA1)0416 Serial Comm. Transmission Error (CALL) 0440 PLC Alarm (PA2)0417 Motor Overload (oL1) 0441 Output Voltage Detection Fault (voF)0418 Drive Overload (oL2) 0442 IGBT Maintenance Time (90%) (TrPC)041A Option Card External Fault (EF0) 0443 Soft Charge Bypass Relay Maintenance Time (LT-3)041B Motor Switch Command Input during Run (rUn) 0444 IGBT Maintenance Time (50%) (LT-4)041D Serial Comm. Transmission Error (CALL) 0445 Braking Transistor Overload (boL)041E Undertorque Detection 1 (UL3) 0448 Motor Overheat (NTC Input) (oH5)041F Undertorque Detection 2 (UL4) 0449 DriveWorksEZ Alarm (dWAL)*1 Drive error code is stored in MEMOBUS/Modbus address 0080 Hex.◆ Identification and Maintenance Functions (I&M)The purpose of the I&M functions is to provide support for the customer during commissioning, parametrizationand repair of the module. SI-EP3 supports I&M function 0, which can be accessed using the Record data object'sread request.Function Record Data IndexI&M0 0xAFF0Structure of the I&M functions is described in Table 8.16.Table 8.16 I&M0 Device Identification (Read-Only)Content Size(Byte) DescriptionHeader 10 -Vendor ID 2 PROFINET Vendor ID of Yaskawa, which is 0x019FOrder ID 20 Order number of the SI-EP3 adapter kit (SI-EP3)Serial number 16 Serial number of the adapterHardware revision 2 Hardware revision of the SI-EP3 adapterSoftware revision 4 Revision of the softwareRevision counter 2 Revision numberProfile ID 2 PROFIdrive (0x3A00)Profile specific type 2 No profile specific type (0x0000)I&M version 2 Version is 1.1 (0x0101)Supported I&M functions 2 I&M0 is supported (0x0001)