B.8 H Parameters: Multi-Function TerminalsH parameters assign functions to the multi-function input and output terminals.u H1: Multi-Function Digital InputsNo.(Addr.Hex) Name Description Values PageH1-03(400)Multi-Function Digital InputTerminal S3 FunctionSelectionTerm S3 Func SelAssigns a function to the multi-function digital inputs through Z2-oo = 3.Refer to Table B.3 for descriptions of setting values.Note: Set unused terminals to F.Default: 24Min.: 3Max.: 60 151H1-04(401)Multi-Function Digital InputTerminal S4 FunctionSelectionTerm S4 Func SelAssigns a function to the multi-function digital inputs through Z2-oo = 4.Refer to Table B.3 for descriptions of setting values.Note: Set unused terminals to F.Default: 14Min.: 3Max.: 60 151H1-05(402)Multi-Function Digital InputTerminal S5 FunctionSelectionTerm S5 Func SelAssigns a function to the multi-function digital inputs through Z2-oo = 5.Refer to Table B.3 for descriptions of setting values.Note: Set unused terminals to F.Default: 3Min.: 3Max.: 60 151H1-06(403)Multi-Function Digital InputTerminal S6 FunctionSelectionTerm S6 Func SelAssigns a function to the multi-function digital inputs through Z2-oo = 6.Refer to Table B.3 for descriptions of setting values.Note: Set unused terminals to F.Default: 4Min.: 3Max.: 60 151H1-07(404)Multi-Function Digital InputTerminal S7 FunctionSelectionTerm S7 Func SelAssigns a function to the multi-function digital inputs through Z2-oo = 7.Refer to Table B.3 for descriptions of setting values.Note: Set unused terminals to F.Default: 6Min.: 3Max.: 60 151Table B.3 H1 Multi-Function Digital Input SelectionsH1-ooSetting Function Description Page3 Multi-Step Speed Reference 1Multi-Step Ref 1When input terminals are set to Multi-Step Speed References 1 through 3, switchingcombinations of those terminals will create a multi-step speed sequence using the frequencyreferences set in d1-01 through d1-08. 1514 Multi-Step Speed Reference 2Multi-Step Ref 2When input terminals are set to Multi-Step Speed References 1 through 3, switchingcombinations of those terminals will create a multi-step speed sequence using the frequencyreferences set in d1-01 through d1-08. 1516 Jog reference selectionJog Freq RefClosed: Jog frequency reference (d1-17) selected. Jog has priority over all other referencesources. 151C Analog terminal input selectionTerm AI EnableOpen: Function assigned by H3-14 is disabled.Closed: Function assigned by H3-14 is enabled. 151F <1> Not Used (Through Mode) Allows serial communications to control the output. 15110 Up commandUp Command 1The drive accelerates when the Up command terminal closes, and decelerates when the Downcommand closes. When both terminals are closed or both are open, the drive holds thefrequency reference. The Up and Down commands must always be used in conjunction withone another.15111 Down commandDown Command 1The drive accelerates when the Up command terminal closes, and decelerates when the Downcommand closes. When both terminals are closed or both are open, the drive holds thefrequency reference. The Up and Down commands must always be used in conjunction withone another.15113 <2> Reverse JogReverse JogClosed: Runs reverse at the Jog frequency d1-17 15214 Fault Reset Closed: Resets faults if the cause is cleared and the Run command is removed. 15319 PI disablePI DisableOpen: PI control enabledClosed: PI control disabled 15324External faultNO/Always DetCoast to StopNormally Open, Always Detected, Coast to Stop 15360 Motor pre-heat 1Motor Preheat 1Closed: Triggers Motor pre-heat 1 153<1> Available in bypass controller software versions VST800298 and later.<2> Available in bypass controller software versions VST800297 and earlier.B.8 H Parameters: Multi-Function TerminalsYASKAWA ELECTRIC SIEP YAIZ1B 01E YASKAWA AC Drive – Z1000 Bypass Technical Manual 323B Parameter List
