u Wire Gauges and Tightening TorqueUse the tables in this section to select the appropriate wires and crimp terminals.Gauges listed in the tables are for use in the United States.Note: 1. Wire gauge recommendations based on drive continuous current ratings using 75 °C 600 Vac vinyl-sheathed wire assuming ambienttemperature within 40 °C and wiring distance less than 100 m.2. Terminal +3 is not used. Do not connect devices or wiring to this terminal.• Consider the amount of voltage drop when selecting wire gauges. Increase the wire gauge when the voltage drop is greaterthan 2% of motor rated voltage. Ensure the wire gauge is suitable for the terminal block. Use the following formula tocalculate the amount of voltage drop:Line drop voltage (V) = 3 × wire resistance (Ω/km) × wire length (m) × current (A) × 10-3• Refer to UL Standards Compliance on page 372 for information on UL compliance.Yaskawa recommends using closed-loop crimp terminals on all drive models. To maintain UL/cUL approval, UL Listedclosed-loop crimp terminals are specifically required when wiring the drive main circuit terminals on models 2A0031 to2A0396 and 4A0034 to 4A0590. Use only the tools recommended by the terminal manufacturer for crimping.Refer to Closed-Loop Crimp Terminal Size on page 372 for closed-loop crimp terminal recommendations.The wire gauges listed in the following tables are Yaskawa recommendations. Refer to NEC table 310-16 for proper wiregauge selection for terminals -M, +M, -1, +3, and ground.n Three-Phase 200 V ClassTable 3.2 Wire Gauge and Torque Specifications (Three-Phase 200 V Class)Model Terminal Recomm. GaugeAWG, kcmilWire RangeAWG, kcmilScrewSizeTightening TorqueN·m (lb. in.)2A0011R/L1, S/L2, T/L3 1414 to 8M4 1.6 to 1.8(14 to 16)U/T1, V/T2, W/T3 14-M, +M –– M5 2.7 to 3.0(24 to 27)2A0017R/L1, S/L2, T/L3 1014 to 8M4 1.6 to 1.8(14 to 16)U/T1, V/T2, W/T3 10-M, +M –– M5 2.7 to 3.0(24 to 27)2A0024R/L1, S/L2, T/L3 814 to 8M4 1.6 to 1.8(14 to 16)U/T1, V/T2, W/T3 8-M, +M –– M5 2.7 to 3.0(24 to 27)2A0031 <1>R/L1, S/L2, T/L3 814 to 8M4 1.6 to 1.8(14 to 16)U/T1, V/T2, W/T3 8-M, +M –– M5 2.7 to 3.0(24 to 27)2A0046 <1>R/L1, S/L2, T/L3 610 to 4 M5 2.7 to 3.0(24 to 27)U/T1, V/T2, W/T3 6-M, +M ––2A0059 <1>R/L1, S/L2, T/L3 410 to 4 M5 2.7 to 3.0(24 to 27)U/T1, V/T2, W/T3 4-M, +M ––2A0075 <1>R/L1, S/L2, T/L3 38 to 2/0 M8 5.4 to 6.0(48 to 53)U/T1, V/T2, W/T3 3-M, +M ––3.8 Main Circuit WiringYASKAWA ELECTRIC TOEP C710616 45F YASKAWA AC Drive – Z1000 User Manual 833 Electrical Installation
