GE N60 Instruction Manual
Also see for N60: Communications manualCommunications guideInstruction manualInstruction manualInstruction manual
                                                                                                                                                                                                                                                                                                                                                                                                                                                                            | |
Contents
|
CHAPTER 5: SETTINGS SYSTEM SETUPN60 NETWORK STABILITY AND SYNCHROPHASOR MEASUREMENT SYSTEM – INSTRUCTION MANUAL 5-1435PMU AGGREGATOR 1 TCP PORT — Selects the TCP port number to be used by this aggregator for network reporting. All ports,even those of unused aggregators, must be valid and unique to avoid port number collisions.PMU AGGREGATOR 1 UDP PORT — Selects the UDP port number to be used by this aggregator for network reporting. All ports,even those of unused aggregators, must be valid and unique to avoid port number collisions.PMU AGGREGATOR 1 PDC CONTROL — The synchrophasor standard allows for user-defined controls originating at the PDC, tobe executed on the PMU. The control is accomplished via an extended command frame. The relay decodes the first wordof the extended field, EXTFRAME, to drive 16 dedicated FlexLogic operands. Each aggregator supports 16 FlexLogicoperands, as shown in the table. The operands are asserted for five seconds following reception of the command frame. Ifthe new command frame arrives within the five-second period, the FlexLogic operands are updated, and the five-secondtimer restarts. This setting enables or disables the control. When enabled, all 16 operands for each aggregator are active;when disabled, all 16 operands for each aggregator remain reset.Table 5-17: FlexLogic operands supported by aggregatorSETTINGS SYSTEM SETUP PHASOR MEASUREMENT UNIT PMU AGGREGATOR 1 90-5 AGGR 1CONFIGURATIONPMU AGGREGATOR 1 NAME — A user-defined visible string of characters (max. 56) to identify the source of the stream. Thisvalue, concatenated with the Aggregator IDCode and Aggregator Class of Service, is mapped into the IEC 61850 MSVIDfiled in the output stream.AGGREGATOR 1: PHYSICAL PORT — This setting determines the physical ports through which the synchrophasor traffic istransmitted. The range is 1, 2, 3.PMU AGGREGATOR 1: UDP PORT — This setting selects the UDP port number that is used by this dataset for network reporting.Default setting values for IEEE C37.118 and IEC 6150-90-5 are provided.Operand type Operand syntax Operand descriptionELEMENT:Synchrophasor, phasor data,concentratorAGTR1 PDC CNTRL 1 Phasor data concentrator asserts control bit 1, asreceived via the networkas above AGTR1 PDC CNTRL 2 Phasor data concentrator asserts control bit 2 asreceived via the networkas above AGTR1 PDC CNTRL 3 Phasor data concentrator asserts control bit 3 asreceived via the networkas above AGTR1 PDC CNTRL 16 Phasor data concentrator asserts control bit 16, asreceived via the networkas above AGTR2 PDC CNTRL 1 Phasor data concentrator asserts control bit 1 asreceived via the networkas above AGTR2 PDC CNTRL 2 Phasor data concentrator asserts control bit 2 asreceived via the networkas above AGTR2 PDC CNTRL 3 Phasor data concentrator asserts control bit 3 asreceived via the networkas above AGTR1 PDC CNTRL 16 Phasor data concentrator asserts control bit 16, asreceived via the network 90-5 AGGR 1 CONFIGURATION PMU AGGREGATOR 1NAME:Range: 56-character ASCII text (blank by default) PMU AGGREGATOR 1:PORT: 1Range: 1, 2, 3 PMU AGGREGATOR 1:UDP PORT: 102Range: 1 to 65534 in steps of 1 PMU AGGREGATOR 1:NUMBER OF ASDUs: 1Range: 1 to 4 |
Related manuals for GE N60
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine