- 327 -9. Operating Management/ Specifications• Other Settings • Fax SettingItem FactorydefaultsettingDescriptionDefault Mode Normal Sets the default screen of fax.Redial Tries 2 time(s) Sets the number of redial attempts.Available range: 0 to 9 timesRedial Interval 1 minute(s) Sets the time between redial attempts.Available range: 0 to 5 minutesBlock Junk Fax Setting OFF Sets Block Junk mode Fax.Registered List Register / Edit (NULL) Register / Edit addresses for Block Junk Faxwhen [Mode2] or [Mode3] is set.Delete Delete addresses for Block Junk Fax when[Mode2] or [Mode3] is set.Ring Response 1 Ring Sets the number of rings required beforereceiving an incoming fax.Dialing Pause Duration 2 second(s) Sets the dial pause time.Available range: 0 to 10 secondsRx Reduc. Rate Auto Sets the reception reduction rate.Reduc. Margin 24 mm (0.9inch) or100 mm (3.9inch)Sets the threshold level of receptionreduction.Available range: 0 to 100 mm (0 to3.9 inches)ECM Mode ON Sets whether to use the error correctionmode.PreFix (NULL) Sets the dialing prefix. You can enter up to 40digits.Received Time Stamp OFF Sets whether to print the time stamp onreceived faxes.Print Check Message ON Sets whether to report the error content if atransmission error occurs.Duplex OFF Sets simplex or duplex for printing receivedfax and the binding position for duplexprinting.Distant Station Priority Type 1 Sets the priority order of information forDistant Station (information of thedestination).Priority (High > Low)[Type 1]: Destination information > Name inspeed dial > Phone number[Type 2]: Name in speed dial > PhonenumberItem FactorydefaultsettingDescriptionService Bit OFF If set to OFF, some menu items are notdisplayed on the screen.Country Code International orU.S.ASets the country code.A/R Full Print ON Sets whether to print the list of thecommunication results automatically afterevery 50 communications.Daily Tx/Rx Log Report Setting OFF Enables / disables to print a daily report.Print Time 0 Hour0 Minute0 SecondSets the date and time for printing the dailyreport.Tone For Echo (For Transmission) Disable Displays only if Service Bit is ON.Tone For Echo (For Reception) Disable Displays only if Service Bit is ON.H/Modem Rate (For Tx) 33.6 Kbps Sets the default modem receptiontransmission speed while the machine issending a fax.H/Modem Rate (For Rx) 33.6 Kbps Sets the default value of the modemtransmission speed while the machine isreceiving a fax.Attenuator 10 dB, Range:0 - 15 dBEnter Attenuator. Displays only if Service Bitis ON.MF Attenuator 8 dB, Range: 0- 15 dBEnter MF(Tone) Attenuator. Displays only ifService Bit is ON.Pulse Make Ratio 40%, Range:33, 39, 40%Sets to make rate of DP (10 pps) during call.Displays only if Service Bit is ON and Tone /Pulse setting is PULSE.Pulse Dial Type N, Range: N,10-N, N+1Sets the pulse type for dialing. Displays onlyif Service Bit is ON and Tone / Pulse settingis PULSE.MF(Tone) Duration 100 mseconds,Range: 75, 85,100 msecondsEnter MF(Tone) Duration. Displays only ifService Bit is ON and Tone / Pulse setting isTONE.Calling Timer 60 mseconds,Range: 1 -255 secondsDisplays only if Service Bit is ON.PBX Line OFF When connecting to PBX (internalexchange), put it to [ON].
