Nautel V10 User's Installation And Operation Manual

Contents

Nautel V10 User's Installation And Operation Manual Manual pdf 81 page image

V10/V7.5/V5/V3.5 Installation and Operation Manual Page 3-23Section 3 Operating Instructions Issue 3.5NOTEPressing the Power - Increase or Decreasebutton at any time, regardless of the GUIscreen, will automatically enter the EditPreset screen for the active preset and willhighlight the Power parameter. If Power -Increase or Decrease is pressed again, thePower parameter will change accordingly.Press Save to activate the change.(b) To edit a preset parameter, highlight thedesired parameter (using f and g) andpress Edit.- Edit the power level, if desired, using thePower - Increase and Decrease buttonsor f and g [for FM mode, eachincrement is 100 W (V10/V7.5) or 50 W(V5/V3.5); for FM+HD and HD modes,each increment is 10 W]; holding thebutton increases the rate of change].- Edit the operating frequency, if desired,using the f and g buttons (in 100 kHzsteps; holding the button increases therate of change).NOTEIf the transmitter’s frequency is changed,ensure the frequency of any associatedequipment (M50, etc.) is also changed.- Edit the mode of operation [FM (analog),HD (all digital), or FM+HD (hybrid)]. If theoperating mode is FM, you can also editthe following parameters:• PA ALC [Y (default) or N]• IPA Power (in watts; 250 W default)• IPA ALC [Y (default) or N]- The above parameters have been factoryset and should not require adjustment.- If you press Edit for any parameter,press Save to activate changes or Backto cancel the edit.- Press Back to return to power controlscreen.3.6.5 View RF Module Status andFan SpeedCritical diagnostic information for the RFpower modules (A - H and IPA modules Aand B for V10 transmitters; A – C, E – G, andIPA modules A and B for V7.5 transmitters;A - D and the IPA module for V5 transmitters;A - C and the IPA module for V3.5transmitters) and cooling fan speed can bemonitored as follows:NOTEThe Module Status menu is displayed formonitoring purposes only. Module statuscannot be altered from this menu.(a) From the main menu, highlight ModuleStatus (using f and g) and pressSelect. A Module Status screen willappear that shows the current and biasvoltage for each PA in the module beingviewed as well as the PA voltage,temperature, intermediate RF level andfan speed.Main MenuPower ControlModule StatusEvents LogSoftware VersionMeters PresetsSelect Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanAMain MenuPower ControlModule StatusEvents LogSoftware VersionMeters PresetsSelect Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanAModule StatusCurr. Bias PA Module AQ1 0 A 0 V PA Volts 0 VQ2 0 A 0 V Temperature 31 CQ3 0 A 0 V Intm RF Lvl 0 VQ4 0 A 0 V Fan Speed 0 RPMReset Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanAModule StatusCurr. Bias PA Module AQ1 0 A 0 V PA Volts 0 VQ2 0 A 0 V Temperature 31 CQ3 0 A 0 V Intm RF Lvl 0 VQ4 0 A 0 V Fan Speed 0 RPMReset Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanAModule StatusCurr. Bias PA Module AQ1 0 A 0 V PA Volts 0 VQ2 0 A 0 V Temperature 31 CQ3 0 A 0 V Intm RF Lvl 0 VQ4 0 A 0 V Fan Speed 0 RPMReset Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanAModule StatusCurr. Bias IPA ModuleQ4 A 0 A 3.25 V PA Volts 0 VQ3 B DSBL 3.35 V Temperature 32 CRF Lvl 0 VReset Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanAModule StatusCurr. Bias IPA ModuleQ4 A 0 A 3.25 V PA Volts 0 VQ3 B DSBL 3.35 V Temperature 32 CRF Lvl 0 VReset Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanA