Nautel V10 User's Installation And Operation Manual

Contents

Nautel V10 User's Installation And Operation Manual Manual pdf 89 page image

V10/V7.5/V5/V3.5 Installation and Operation Manual Page 3-31Section 3 Operating Instructions Issue 3.5NOTEThe options in the System Config fieldmay vary depending on a particularcustomer’s system requirements.The RF Modules field represents theconfiguration of the transmitter,particularly the RF power modules.Changing from Analog to Digital mode,the IPA Input Low threshold changes from12 W to 6 W (V10/V7.5) or from 6 W to3 W (V5/V3.5) to accommodate thebiasing on the IPA module(s).(b) Press Save to store the setting. PressBack to return to previous menu.3.6.12.8 Save/Recall Factory SettingsThe functions described in paragraphs3.6.12.1 through 3.6.12.7 can be restoredto factory settings as follows:(a) Use f or g to highlight Save FactorySettings or Recall Factory Settingsand press Select. Carefully read theappropriate WARNING message, thenpress Yes to activate the change.3.6.12.9 NxLink ConfigurationConfigure the NxLink, if installed, asfollows:NOTEThe Hardware Settings screen onlydisplays NxLink Configuration if theNxLink is installed and communicatingwith the transmitter’s controller.(a) Use f or g to highlight IP Address,Netmask, Gateway or DNS Server.Press Select on the address to beedited.NOTEThe DHCP’d Address is not a selectablefield. The address is automaticallyassigned when the NxLink is connected toa LAN (if DHCP is available on thenetwork) and the IP Address is set to0.0.0.0 (as shown).(b) Press Edit on the highlighted addressfield to enable editing of the address.Use f or g to move left to rightthrough the address sections.(c) Press Save when complete.(d) Press Back to return to the mainscreen.Save Factory SettingsWARNING: This will overwrite factorydefault settings with the currentsettings. Do you wish to proceed?Yes No11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASave Factory SettingsWARNING: This will overwrite factorydefault settings with the currentsettings. Do you wish to proceed?Yes No11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanAORRecall Factory SettingsWARNING: This will replace currentsettings with the factory defaultsettings. Do you wish to proceed?Yes No11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanARecall Factory SettingsWARNING: This will replace currentsettings with the factory defaultsettings. Do you wish to proceed?Yes No11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanASave/Recall Factory SettingsSave Factory SettingsRecall Factory SettingsSelect Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASave/Recall Factory SettingsSave Factory SettingsRecall Factory SettingsSelect Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanA11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanANxLink ConfigurationIP Address: 0 .0 .0 .0Netmask: 0 .0 .0 .0Gateway: 0 .0 .0 .0DNS Server: 0 .0 .0 .0DHCP’d Address: 192.168.1.60Save Select Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanANxLink ConfigurationIP Address: 0 .0 .0 .0Netmask: 0 .0 .0 .0Gateway: 0 .0 .0 .0DNS Server: 0 .0 .0 .0DHCP’d Address: 192.168.1.60Save Select Back