Nautel V10 User's Installation And Operation Manual

Contents

Nautel V10 User's Installation And Operation Manual Manual pdf 88 page image

Page 3-30 V10/V7.5/V5/V3.5 Installation and Operation ManualIssue 3.5 Section 3 Operating Instructions(c) Press Save to store the setting.(d) Press Back to return to previousmenu.3.6.12.7 System ConfigurationThe system configuration is factory set tothe customer’s requirements. No useradjustment should be required.(a) Use f or g to highlight SystemConfig, RF Modules, FM+HD Bias orALC Limit. Press Edit on the desiredfield and use f or g to selectbetween the available options:• System Config: Stand Alone, Exctr.Ctrl: Master, Exctr,Ctrl: Slave or SC1• RF Modules: Analog or Digital• FM+HD Bias: FM+HD or HD (allowsthe use of HD bias levels in FM+HDmode)• ALC Limit: adjust between 65% and135% (typical range is 95 -105 %)• Exc Chgovr Dly (FM): adjust the timedelay for an exciter changeover (in FMmode only) between 1 and 60 s• Preset Synch: Enable (default setting;forces the M50 to select the sameactive preset as the transmitter) orDisableNOTEThe preset synchronization feature onlyselects the M50’s preset. The associatedpreset parameters (mode, frequency, etc.)on the M50 must still be manuallymatched to the transmitter.The M50’s firmware must support thepreset synchronization feature. If you areunsure of the M50’s firmwarecompatibility, set the Preset Synch toDisable.Top of ScreenSystem ConfigurationSystem Config: Stand AloneRF Modules: AnalogFM+HD Bias: FM+HDALC Limit: 100%Exc Chgovr Dly(FM):1 sEdit Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanASystem ConfigurationSystem Config: Stand AloneRF Modules: AnalogFM+HD Bias: FM+HDALC Limit: 100%Exc Chgovr Dly(FM):1 sEdit Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanABottom of ScreenSystem ConfigurationRF Modules: AnalogFM+HD Bias: FM+HDALC Limit: 100%Exc Chgovr Dly(FM):1 sPreset Synch: EnableEdit Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanASystem ConfigurationRF Modules: AnalogFM+HD Bias: FM+HDALC Limit: 100%Exc Chgovr Dly(FM):1 sPreset Synch: EnableEdit Back11:26 98.10MHz 0.00kW 1 ExA IPAA/A FanAE-H (or E-G for V7.5) Rej Pwr High andO/P Rej Pwr High used in V10/V7.5only. Display reads Unused for V5/V3.5.4/43/41/42/4Setup ThresholdsPreset 1 98.10 MHz FM 5.50 kWSWR Shutback 600 WIPA Forward High 350 WIPA Forward Low 50 WEdit Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASetup ThresholdsPreset 1 98.10 MHz FM 5.50 kWSWR Shutback 600 WIPA Forward High 350 WIPA Forward Low 50 WEdit Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASetup ThresholdsPreset 1 98.10 MHz FM 5.50 kWIPA Forward vs Volts 0%IPA Input High 19 WIPA Input Low 3 WEdit Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASetup ThresholdsPreset 1 98.10 MHz FM 5.50 kWIPA Forward vs Volts 0%IPA Input High 19 WIPA Input Low 3 WEdit Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASetup ThresholdsPreset 1 98.10 MHz FM 5.50 kWIPA Reflected High 75 WA-D Rej Pwr Shutback 600 WE-H Rej Pwr Shutback 600 WEdit Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASetup ThresholdsPreset 1 98.10 MHz FM 5.50 kWIPA Reflected High 75 WA-D Rej Pwr Shutback 600 WE-H Rej Pwr Shutback 600 WEdit Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASetup ThresholdsPreset 1 98.10 MHz FM 5.50 kWO/P Rej Pwr Shutback 600 WLow Forward Power 50 %Edit Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanASetup ThresholdsPreset 1 98.10 MHz FM 5.50 kWO/P Rej Pwr Shutback 600 WLow Forward Power 50 %Edit Back11:26 98.10MHz 0.00kW 1 EXA IPAA/A FanA