Panasonic DMR-E60 Operating Instructions Manual

Also see for Diga DMR-E60: Operating instructions Firmware instructions Operating instructions

Contents

34Timer recording (continued)4 Press [ENTER] (10) when you have finished makingchanges.≥To continue programming:Repeat steps 2, 3 and 4.5 Press [PROG/CHECK] (13) or [RETURN] (28).To put the unit on recording standbyPress [ , TIMER] (14).Ensure “ ” lights on the unit’s display.To change the timer recording programme1) While the Timer Programme List Screen is being shown, use[3, 4] (10) to select the programme you want to change, andpress [ENTER] (10) to show the Timer Programme Correctionscreen.≥You may also select programme by inputting a 2-digit numberusing the numeric buttons (4).≥Use [2, 1] (10) to move to the page preceding or followingthe one on display.2) Move through the items with [1] (10) and change the settingswith [3, 4] (10) and press [ENTER] (10).Note≥The built-in clock employs 24-hour system.≥The remaining time is not shown if you insert discs other thanDVD-RAM or DVD-R.≥The remaining time displayed is calculated based on the currentrecording mode.≥If the disc is protected (pages 37, 74), the unit switches tostandby but does not go on standby for recording. Check the disccarefully.≥Recording is not possible unless you set “Disc Protection” in“DISC INFORMATION” to “Off”. (page 37)≥You cannot record to a disc if the write protect tab on a cartridgedisc is set to protect. Release this before operation (page 74).≥Even if the unit is put in the timer recording standby mode or thetimer recording is being performed, you can play a programme.≥If the unit is not put in the timer recording standby mode at thelatest 10 minutes before the programmed timer recording startingtime, the [ ] flashes on the unit display. In this case, press the[ , TIMER] (14) button to put the unit in the timer recordingstandby mode.≥When recording more than one programme in a row, forDVD-RAM the first few seconds, and for DVD-R about the first30 seconds of all programmes from the second one onwards willnot be recorded.To check programmes[RAM] [DVD-R]Press [PROG/CHECK] (13).The Timer Programme List screen appears.Icon explanations (A)¥ This programme is currently recording.W The programme is overlap with another programme.F The disc was full or the maximum number of programmes orscenes was reached so the programme failed to record.The television programme was copy-guarded so theprogramme failed to record.X The programme did not complete recording because thedisc is dirty or some other reason.Disc space (B)OK: Displayed if the recording can fit in the remainingspace on the disc. However, when the programmebecomes longer than scheduled during therecording by setting “PDC” to “ON”, theprogramme may not be recorded until its end.# (Date): For recordings made daily or weekly, the displaywill show until when recordings can be madebased on the time remaining on the disc.!: Displayed if the disc is not inserted in the unit or iswrite-protected (pages 37, 74) or there is notenough memory capacity left on the disc.ªTo change the programmeSee at left.ªTo exit from the Timer Programme List screenPress [PROG/CHECK] (13) or [RETURN] (28). (The television isshown.)For your reference≥Programmes that failed to record are deleted from the list at 4a.m. the day after tomorrow.Starting and canceling programmes[RAM] [DVD-R]ªTo put the unit on recording standbyPress [ , TIMER] (14).The unit turns off and “ ” lights on the unit’s display.Note≥The unit cannot go to timer recording standby if the disc isprotected (pages 37, 74) or full (“ ” flashes). Check the disccarefully.ªTo release the unit from recording standbyIf you want to record something else before the programme starttime, for example:Press [ , TIMER] (14).The unit turns on and “ ” goes out.≥Be sure to press [ , TIMER] (14) before the programme starttime to put the unit on recording standby. The programme onlyworks if “ ” is on.ªTo stop recording while a programme is workingPress [ , TIMER] (14).To clear a timer recording programme[RAM] [DVD-R]Press [CANCEL] (5) or [ERASE] (32) while theprogramme’s Timer Programme Correction screen isbeing shown.(Alternatively, use [3, 4] (10) to select the programmein the Timer Programme List screen and press[CANCEL] (5) or [ERASE] (32).)≥You can not delete programmes that are currently recording.RETURNSELECTSP OK1:221:19BBC 1 15/ 7 TUE01Mode DiscspaceStopStartNo. Name Date1:58 SPTIMERRECORDING Remain1:19:00 15.7 TUEENTERCANCELOFFPDCNew Timer ProgrammeWFX02030405BBC 1BBC 1BBC 1BBC 115/ 7 TUE23/ 7 WED23/ 7 WED23/ 7 WED1:208:009:0010:002:209:0010:0011:00SPSPSPSPOFFOFFOFFOFFOKOKOKOKA B