Panasonic DMR-E60 Operating Instructions Manual

Also see for Diga DMR-E60: Operating instructions Firmware instructions Operating instructions

Contents

54Editing still pictures (continued)Othersª Slide Show Intervals[SD/CARD] [RAM]You can set the display timing of slide show. (page 50)After performing steps 1 to 2 of “Displaying still pictures(Album Display)” (page 50), perform the following steps:3 Use [3, 4] (10) to select “Others” and press[ENTER] (10).4 Confirm that “Slide Show Intervals” is selected anduse [2, 1] (10) to select the desired timingbetween still pictures (0–30 seconds) (in base unitsof 1 second).5 Press [ENTER] (10).ª Format[SD/CARD]You can erase all still pictures in the SC/PC cards.Once activated, recorded contents (including protected stillpictures and computer data) will be completely erased. Checkit carefully before proceeding.After performing steps 1 to 2 of “Displaying still pictures(Album Display)” (page 50), perform the following steps:3 Use [3, 4] (10) to select “Others” and press[ENTER] (10).4 Press [3, 4] (10) to select “Format” and use[2, 1] (10) to select “SD CARD” or “PC CARD”and then press [ENTER] (10).≥The confirmation screen appears.5 Press [2, 1] (10) to select “Yes” and press[ENTER] (10).≥The confirmation screen appears.6 Press [2, 1] (10) to select “Start” and press[ENTER] (10).≥Format begins.7 Press [ENTER] (10) to complete the procedure.ª To stop partway throughSelect “Cancel” in step 6 and press [ENTER] (10).OrPress [RETURN] (28).Note≥The cards formatted on this unit may not be usable on otherequipment.JPEGOthers OthersSlide Show Intervals 5 sec.FormatRETURNENTERSELECTSD CARDJPEGOthers OthersSlide Show Intervals 5 sec.FormatRETURNENTERSELECTSD CARDDV Automatic Recording(DV AUTO REC)[RAM]Automatic generation of programmes and play lists is possible forusing the “DV AUTO REC” function when connecting DVequipment (e.g., Digital Video Camera) to the DV input terminal onthe front of the unit with the DV cable. Recordings from DVcameras can be recorded to DVD-RAM and DVD-R media,however the “DV AUTO REC” function cannot be used with DVD-R.Preparation≥Before connecting any cables, first make sure that the power forboth units is off.Then after connecting any cable, turn on the both units.≥Connect the DV equipment to the DV input terminal on the frontpanel. (page 59)≥Pause play of the DV equipment at the point you want recordingto start.≥Switch [DVD, TV] (19) to “DVD”.Recording to the disc:Insert a disc that can be written to.- Check that disc can be recorded on (page 10).- Ensure the write protect tab is not set to “PROTECT”(page 74).- Ensure the disc is not write-protected with DISCINFORMATION (page 37).1 While stoppedPress [REC MODE] (33) to select the recordingmode.≥Select “XP”, “SP”, “LP”, or “EP”.2 Press [FUNCTIONS] (11).3 Use [3, 4, 2, 1] (10) to select “DV AUTO REC”and press [ENTER] (10).≥The DV equipment pauses automatically if it was playing.4 Use [2, 1] (10) to select “Rec” and press [ENTER](10).≥Recording starts.DV AUTO RECRETURNENTERRec CancelDV AUTO RECModel of DV PanasonicNV-Remain 01:04(SP)