Yamaha TT-R125(N) 2000 Owner's Service Manual

SPEC2 - 17MAINTENANCE SPECIFICATIONSNOTE:1. First, tighten the ring nut approximately 38 Nm (3.8 m • kg, 27 ft • lb) by using the ring nutwrench and turn the steering right and left a few times; then loosen the ring nut one turn.2. Retighten the ring nut 20 Nm (2.0 m • kg, 14 ft • lb).Part to be tightened Thread size Q’ty Tightening torqueNm m•kg ft•lbUpper bracket and inner tube M8 × 1.25 2 25 2.5 18Lower bracket and inner tube M10 × 1.25 2 60 6.0 43Upper bracket and steering stem M22 × 1.0 1 110 11.0 80Handlebar upper holder and upper bracket M8 × 1.25 4 23 2.3 17Steering stem and ring nut M25 × 1.0 1 Refer to NOTE.Front fork and cap bolt M25 × 1.0 2 23 2.3 17Front fork and damper rod M10 × 1.0 2 23 2.3 17Front fork and brake cable holder M6 × 1.0 1 7 0.7 5.1Number plate M6 × 1.0 1 7 0.7 5.1Starter knob M11 × 1.25 1 1 0.1 0.7Starter knob stay M6 × 1.0 2 10 1.0 7.2Grip cap upper and lower M5 × 0.8 2 4 0.4 2.9Throttle cable cap M4 × 0.7 2 2 0.2 1.4Brake lever mounting (bolt) M6 × 1.0 1 7 0.7 5.1Brake lever mounting (nut) M6 × 1.0 1 7 0.7 5.1Brake lever holder M5 × 0.8 2 4 0.4 2.9Clutch lever mounting (bolt) M6 × 1.0 1 7 0.7 5.1Clutch lever mounting (nut) M6 × 1.0 1 7 0.7 5.1Clutch lever holder M5 × 0.8 2 4 0.4 2.9Front wheel axle and axle nut M12 × 1.25 1 45 4.5 32Front brake camshaft lever and camshaft M6 × 1.0 1 10 1.0 7.2Rear wheel axle and axle nut M12 × 1.25 1 60 6.0 43Rear brake camshaft lever and camshaft M6 × 1.0 1 10 1.0 7.2Brake pedal mounting M10 × 1.25 1 30 3.0 22Brake pedal position locknut M6 × 1.0 1 7 0.7 5.1Front wheel nipple (spoke) — 36 2 0.2 1.4Rear wheel nipple (spoke) — 36 3 0.3 2.2Driven sprocket and wheel hub M8 × 1.25 4 26 2.6 19Sidestand mounting (nut) M10 × 1.25 1 44 4.4 32Engine mounting:Engine bracket (front) and frame M8 × 1.25 2 40 4.0 29Engine bracket (front) and engine M8 × 1.25 2 40 4.0 29Engine bracket (upper) and frame M8 × 1.25 2 40 4.0 29Engine bracket (upper) and cylinder head M8 × 1.25 1 40 4.0 29Engine and frame (rear) M8 × 1.25 2 40 4.0 29Pivot shaft and nut M12 × 1.25 1 53 5.3 38Relay arm and swingarm M12 × 1.25 1 53 5.3 38