Tascam TM-D4000 Owner's Manual

Also see for TM-D4000: Operation manual Technical documentation

Contents

Index A - DIndex - 1Aadatejecting tapes 9–3lightpipe 1–3, 3–3machine control 9–1, 9–8word sync 3–3 , 9–8adat devices 1–3, 9–8adding effects T–6adding the internal effect T–7adjusting EQ T–5adjusting monitoring volume 5–13AES/EBU 1–3as word sync source 3–3input 1–4, 13–3ALL INPUT key 12–6ALL SAFE key 9–3 , 12–5analog audio 14–1analog inputs 13–1analog output 13–2analog pad 13–1arming tracks T–9ASSIGN key 12–3assigning a dynamics processor to a module 4–6assignment of bussesin snapshot 00 8–1assignment of busses in surround mode 6–1assignment of channels to busses 4–3, 4–4, 12–3, T–4 , T–5, T–9, T–10assignment of modules in surround mode 6–2audio connections T–1auto module select 3–5AUTO MON 12–6auto punch operations 9–7auto-detect (machine control) 9–1 , 9–2automation control 12–1automation fader inhibit 3–5Automation settings 11–3automation setup 14–4AUX 1 through AUX 6 keys 12–2Aux 1&2 as monitor busses 5–13AUX 1–8 outputs 14–2AUX Fader control 4–5AUX OUTPUTS 13–2Aux send fader mode 2–4 , 4–5Aux sends 4–4, 4–4 , 13–2, T–8in cascade 11–2in snapshot 00 8–1internal processor 7–1, T–7linking 4–2metering 4–10pre-fader/post-fader 4–4, 4–5, 7–1 , 12–2, 13–2, T–8Bbalance 4–7, 12–2balance level 3–5block diagram 14–7buss and Aux send metering 4–10BUSS ASSIGN keys 12–3buss assignmentwith the ASSIGN key for 4–4buss delay 4–10, 6–2bypass 4–3, 12–3, T–5bypassing EQ 4–3, 4–4, 12–3, T–5Ccascade 11–1, 11–3connections 11–1, 13–4IPS 11–4monitoring 11–3option settings 11–3PFL 11–3slave 9–9snapshot library 11–4talkback 11–4using 11–3word sync 11–3CASCADE IN and CASCADE OUT 13–4channel-to-buss assignmentssee “assigning channels to busses”CHASE 9–2checking fader and cut status 4–9chorus (effect) 7–2clearing all soloed channels 5–15clearing group settings 4–9clock and Fs indicators 12–1clock and synchronization 14–3clock check 3–4clock settings 3–4see also “word sync”clock tolerance 3–4Clock variationssee also “varispeed” 3–4compressor/limiter settings 4–6computer communications (automation ) 14–5configuration keys 12–2control roomsee “CR”CR and STUDIO 5–13CR level 13–3CR monitoring 5–13CR outputs 14–2creating a list of machine control mapping memories 9–4cueing mode 9–5current version number 10–5cursor keys 12–6cut groups 4–9, T–12CUT key and indicator 12–4cut status 4–9DD IN 1(XLR-type) 13–3D IN 2 (RCA) 13–3data dumps 8–1, 8–3, 8–6data entry controls 12–6de-esser 7–2