Tascam TM-D4000 Owner's Manual

Also see for TM-D4000: Operation manual Technical documentation

Contents

14 - Specifications, etc.14–314.5 Physical specifications14.6 Error and warning messagesNot every one of these messages indicates an error.The purpose of some of these messages is to let youknow that the status of some of the parameters of theTM-D4000 have changed.“User” messages, i.e. those which result from aninvalid entry or selection, are marked with a l.“Confirm” messages, where a response may be nec-essary to confirm an action or setting, are marked bya 4.“Fatal” messages, where the TM-D4000 may eitherbe powered down and reset, or where attention by aqualified service engineer is required, are marked bya 8.14.6.1 Clock and synchronization14.6.2 GeneralPower requirements120V AC, 60 Hz (U.S.A./Canada)230V AC, 50 Hz (Europe)240V AC, 50 Hz (Australia)Power consumption 60WDimensions of mainunit (w x h x d) mm(in.)644 x 237 x 703 (25.4 x 9.3 x 27.7)Weight 26 kg (57.2 lbs)4New clock sourceout of range,Master Clock isunchangedThe selected clock sourceis outside the limits of tol-erance (44.1 kHz or 48 kZ,±6%)4 Flags NGA digital audio source hasbeen selected as a clocksource, but the flags in thedata show that it cannot beused for this purpose4 PLL Unlocked, somixer muted.The clock signal at thedesignated connector isunstable. To avoid dam-age to the monitoringequipment, the TM-D4000mutes itself.4Master Clock hasgone out ofrange, MixermutedThe clock signal at thedesignated connector ismore than 6% out of thenuminal frequency. Toavoid damage to the moni-toring equipment, the TM-D4000 mutes itself.l Can't selectCascade clockfrom this screenThe Cascade option isautomatically set and can-not be changed from theclock screenlYou can't changethe clock sourcewhen cascadeslave isselectedA cascade slave cannothave its clock sourcechanged.4 Please selectINIT clockto change FSOnly the internal sourcecan change the samplingfrequency. Select the INTsource to change the sam-pling frequency4 There is no cardin slotxAn attempt has been madeto select an empty slot asa clock source4 The AD/DA boardhas no clocksourceAn IF-AD4000 interfacecard cannot be used as aclock source4 Mixer will mutewhile chckingWhen checking trhe clocksource, the TM-D4000mutes4 Clock checkresults...The result of a clock checkoperation4 Copy to all bussdelayConfirmation that the samedelay is to be applied to allbusseslCan't UnlinkDynamics withINPUT ChannelslinkedIf a pair of channels hasbeen stereo linked, thedynamics processors can-not be unlinked.l Can't UnlinkDynamics for ST-INxThe dynamics processorscannot be unlinked for thestereo input channelsl Can't UnlinkDynamics forSTEREO OUTThe dynamics processorscannot be unlinked for thestereo outputl Automation ModeSelectConnfirms that Automa-tion Mode is entered, toremind you that the SELkeys now work with theAutomation software.l Select StereoMode Reminder that s achangehas been made to a partic-ular surround mode or tothe stereo mode from asurround model Select SurroundMode 2 + 2l Select SurroundMode 3 + 1l Select SurroundMode 5.1l No Category forAES/EBUAn attempt was made tochange the SCMS settingon professional format out-put datal New Category:xxxConcerned with SCMSsettingsl New SCMS: xxx Concerned with SCMSsettings