Example of the show ip bgp community CommandTo view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode. To view a route mapconfiguration, use the show route-map command in EXEC Privilege mode.To view BGP routes matching a certain community number or a pre-defined BGP community, use the show ip bgp communitycommand in EXEC Privilege mode.Dell>show ip bgp communityBGP table version is 3762622, local router ID is 10.114.8.48Status codes: s suppressed, d damped, h history, * valid, > best, i - internalOrigin codes: i - IGP, e - EGP, ? - incompleteNetwork Next Hop Metric LocPrf Weight Path* i 3.0.0.0/8 195.171.0.16 100 0 209 701 80 i*>i 4.2.49.12/30 195.171.0.16 100 0 209 i* i 4.21.132.0/23 195.171.0.16 100 0 209 6461 16422 i*>i 4.24.118.16/30 195.171.0.16 100 0 209 i*>i 4.24.145.0/30 195.171.0.16 100 0 209 i*>i 4.24.187.12/30 195.171.0.16 100 0 209 i*>i 4.24.202.0/30 195.171.0.16 100 0 209 i*>i 4.25.88.0/30 195.171.0.16 100 0 209 3561 3908 i*>i 6.1.0.0/16 195.171.0.16 100 0 209 7170 1455 i*>i 6.2.0.0/22 195.171.0.16 100 0 209 7170 1455 i*>i 6.3.0.0/18 195.171.0.16 100 0 209 7170 1455 i*>i 6.4.0.0/16 195.171.0.16 100 0 209 7170 1455 i*>i 6.5.0.0/19 195.171.0.16 100 0 209 7170 1455 i*>i 6.8.0.0/20 195.171.0.16 100 0 209 7170 1455 i*>i 6.9.0.0/20 195.171.0.16 100 0 209 7170 1455 i*>i 6.10.0.0/15 195.171.0.16 100 0 209 7170 1455 i*>i 6.14.0.0/15 205.171.0.16 100 0 209 7170 1455 i*>i 6.133.0.0/21 205.171.0.16 100 0 209 7170 1455 i*>i 6.151.0.0/16 205.171.0.16 100 0 209 7170 1455 i--More--Changing MED AttributesBy default, Dell Networking OS uses the MULTI_EXIT_DISC or MED attribute when comparing EBGP paths from the same AS.To change how the MED attribute is used, enter any or all of the following commands.• Enable MED comparison in the paths from neighbors with different ASs.CONFIG-ROUTER-BGP modebgp always-compare-medBy default, this comparison is not performed.• Change the bestpath MED selection.CONFIG-ROUTER-BGP modebgp bestpath med {confed | missing-as-best}• confed: Chooses the bestpath MED comparison of paths learned from BGP confederations.• missing-as-best: Treat a path missing an MED as the most preferred one.To view the nondefault values, use the show config command in CONFIGURATION ROUTER BGP mode.Changing the LOCAL_PREFERENCE AttributeIn Dell Networking OS, you can change the value of the LOCAL_PREFERENCE attribute.To change the default values of this attribute for all routes received by the router, use the following command.208 Border Gateway Protocol IPv4 (BGPv4)
