Panasonic PT-RZ21K Operating Instructions Manual

Also see for PT-RS20K: Command list Operating instructions Operating instructions

Contents

Chapter 4 Settings — [PROJECTOR SETUP] menuENGLISH - 167[MAIN/SUB VERSION] Displays the main and sub versions of the firmware of the projector.[INTAKE AIR TEMP.]*1 Displays the status of the intake air temperature of the projector.[OPTICS MODULE TEMP.] *1 Displays the status of the internal temperature of the projector.[EXHAUST AIR TEMP.]*1 Displays the status of the exhaust air temperature of the projector.[LIGHT1 TEMP.] *1 Displays the light source 1 temperature status of the projector.[LIGHT2 TEMP.] *1 Displays the light source 2 temperature status of the projector.[SELF TEST] Displays the status of the projector.[INPUT] Displays the input terminal currently selected.Displays the representative input terminal when one image is displayed with multiple input signals.[SIGNAL NAME] Displays the input signal name.[MEMORY NO.] Displays the memory number of the input signal.[BACKUP INPUT STATUS] Displays whether switching to the backup input signal is possible or not when [BACKUP INPUTMODE] is set to [OFF]. (x page 119)[NUMBER OF REGISTEREDSIGNAL] Displays the number of registered signals.[COOLING CONDITION] Displays the set cooling conditions.[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.[REMOTE2 STATUS] Displays the control status of the REMOTE2.[AC VOLTAGE] Displays the input supply voltage.[LENS TYPE]*2 Displays the type name (type of the projection lens) set to the projection lens.[LENS ID]*2 Displays the ID set to the projection lens.[LENS NAME] *2 Displays the name set to the projection lens.[LENS THROW RATIO]*2 Displays the range of throw ratio supported by the projection lens in accordance with the [LENSTYPE] setting.[LENS ZOOM TYPE]*2 Displays the drive method of the zoom motor attached to the projection lens.[ZOOM CALIBRATION]*2 Displays the zoom calibration result ([OK]/[FAILED]) and the calibration date.[ON COUNT][POWER ON TIMES] Displays the number of times the power is turned on.[MECHANICAL SHUTTER] Displays the number of times the mechanical shutter is closed.It is counted when [MECHANICAL SHUTTER] is set to [ENABLE].[OPERATING MODE] Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →[OPERATING MODE].[NORMAL] Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].[ECO] Displays the runtime of the light source with [OPERATING MODE] set to [ECO].[USER1] Displays the runtime of the light source with [OPERATING MODE] set to [USER1].[USER2] Displays the runtime of the light source with [OPERATING MODE] set to [USER2].[USER3] Displays the runtime of the light source with [OPERATING MODE] set to [USER3].[CONSOLIDATED RUNTIME]*3Converts the total runtime of the light sources with [OPERATING MODE] set to each item into thetime used with the [NORMAL] setting.The converted runtime is used for a rough indication about when to perform maintenance when theprojector is used in combination of each item in [OPERATING MODE].[UPGRADE KIT][ET-UK20] Displays the activation status by the Upgrade Kit (Model No.:ET-UK20).[ET-CUK10] Displays the activation status by the Auto Screen AdjustmentUpgrade Kit (Model No.: ET‑CUK10).[SIGNAL INFORMATION][INPUT]Displays the input terminal used for the projected image.Displays the representative input terminal when one image isdisplayed with multiple input signals.[SIGNAL FORMAT] Displays the format of the input signal.[LINK] Displays the [SDI LINK] setting.Displays the determination result of the signal when set to [AUTO].[2D/3D] Displays the determination results of the 2D/3D display[SIMUL]Displays the [SIMUL INPUT SETTING] setting.Displays the determination result of the signal when set to[AUTO(3D)] or [AUTO(2D)].[COLOR FORMAT] Displays the color format of the input signal.[SAMPLING] Displays the sampling information of the input signal.[BIT DEPTH] Displays the gradation of the input signal.[SIGNAL LEVEL] Displays the signal level of the input signal.