Panasonic PT-VW355N Operating Instructions Manual

Also see for PT-VW355N: Operating instructions

Contents

f [AMBIENT LIGHT DETECTION] will not work correctly when placing some objects on the ambient luminance sensor.Setting [POWER MANAGEMENT] in step 3)Set the operation as following if there is no signal input.1) Press as to select [POWER MANAGEMENT].2) Press qw to switch the item.f The items will switch each time you press the button.[SHUT DOWN] The countdown timer is displayed after 30 seconds without input signal. The projection lamp is turnedoff and cooled down when reached the set time, then the projector enter into standby status.[OFF] Power management function is off.[READY]The countdown timer is displayed after 30 seconds without input signal. The projection lamp turns offand cools down when reaching the set time, meanwhile the projector is in the power managementmode. The projection lamp will be turned on if the input signal is reconnected or any button is pressed.Setting [TIMER]The timer can be set to 5-120 minutes. The increment is 5 minutes.1) Press as to select [TIMER].2) Press qw to set the timer (5-120 MIN.).f The time will switch each time you press the button.Notef The factory default setting for [TIMER] is [15 MIN.].Setting [STANDBY MODE] in step 3)Set the operation mode during standby. The default setting is [ECO] that keeps power consumption low during standby. Whenthe network function or the serial communication function is used during standby, set to [NORMAL].1) Press as to select [STANDBY MODE].2) Press qw to switch the item.f The items will switch each time you press the button.[ECO] Select this item to reduce power consumption during standby.[NORMAL] Select this item to use the network function or the serial communication function during standby.[NETWORK] Select this item to reduce power consumption during standby, and to operate the projector via thewired LAN or the serial communication function by using the Wake on LAN function.Notef If [STANDBY MODE] is set to [ECO], you cannot use network functions when the projector is standing by. Also, you cannotuse some RS-232C protocol commands.f When set to [ECO], it may take approx. 10 seconds longer before the projector starts projecting after the power is turned on,compared with when [NORMAL] is set.f If [STANDBY MODE] is set to [NETWORK], it takes less power consumption than it is set to [NORMAL].f When [STANDBY MODE] is set to [NETWORK], it will be no restriction for network function and serial communicationfunction within 60 seconds when the Wake on LAN function is working.f The setting of [STANDBY MODE] cannot be returned to the factory default even if the [PROJECTOR SETUP] menu →[INITIALIZE ALL] is executed (x page 84).[EMULATE]When controlling the projector on a computer via the terminal, set use of control commands on a previouslypurchased Panasonic projector. This allows the control software for an existing Panasonic projector to be inherited and used.1) Press as to select [EMULATE].2) Press the button.f The [EMULATE] screen is displayed.3) Press as to select one item.[DEFAULT]VW355N series, VX425N series, VZ575N series, VW535N series, VX605N series, VZ570 series,VW530 series, VX600 series, EZ580 series, EW640 series, EX610 series, EW540 series,EZ770 series, EW730 series, EX800 series, VW345N series, VX415N series, VW340Z, VX410Z,VX42Z, RZ475 series, RZ470 series, RW430 series, RZ370 series, RW330 series[D3500] D3500 series[D4000] D4000 series[D/W5k SERIES] D5700 series, DW5100 series, D5600 series, DW5000 series, D5500 series80 - ENGLISHChapter 4 Settings - [PROJECTOR SETUP] menu