5.5 E: Motor Parameters220 YASKAWA ELECTRIC SIEP C710616 27G YASKAWA AC Drive A1000 Technical Manual E3-04 to E3-13Parameters E3-04 through E3-13 set up the V/f pattern used for motor 2 as shown in Figure 5.57.Note: Certain E3- parameters might not be visible depending on the control mode. Refer to Parameter Table on page 453.Figure 5.57Figure 5.57 V/f Pattern for Motor 2Note: 1. The following conditions must be true when setting up the V/f pattern: E3-09 E3-07 E3-06 E3-11 E3-042. To make the V/f pattern a straight line at a frequency lower than E3-06, set E3-09 = E3-07. With this setting, E3-08 is disregarded.3. Parameters E3-04 through E3-13 are reset to their default values when the drive is initialized.4. E3-11, E3-12, and E3-13 rarely need to be changed, and should only be used to fine-tune the V/f pattern in the constant output range. E4: Motor 2 ParametersE4 parameters contain the motor data for motor 2. These parameters are usually set automatically during theAuto-Tuning process (Rotational Auto-Tuning, Stationary Auto-Tuning 1 and 2). If Auto-Tuning cannot be performed,refer to Auto-Tuning Fault Detection on page 360 for detail.Note: As the function for switching between two motors cannot be used with a PM motor, the E5- parameters will be hidden whena PM motor control mode is selected (A1-02 = 5, 6, or 7). E4-01: Motor 2 Rated CurrentSet E4-01 to the full load amps (FLA) stamped on the nameplate of motor 2. This value is used for motor protection andto calculate torque limits. If Auto-Tuning completes successfully, the value entered to T1-04 will automatically be savedto E4-01.Note: 1. Display is in the following units. CIMR-A2A0004 to 2A0040, CIMR-A4A0002 to 4A0023: 0.01 A units CIMR-A2A0056 to 2A0312, CIMR-A4A0031 to 4A0675: 0.1 A units CIMR-A4A0930 to 4A1200: 1 A units2. If the motor rated current in E4-01 is set lower than the motor no-load current in E4-03, then a parameter setting error will occur(oPE02). E4-03 must be set correctly to prevent this error.No.<1> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.<2> Default setting is determined by the control mode selected for motor 2 (E3-01).<3> The drive sets this value when Auto-Tuning is performed (Rotational Auto-Tuning and Stationary Auto-Tuning 1, 2).<4> Parameter ignored when E3-11 and E3-12 are set to 0.0.Parameter Name Setting Range DefaultE3-04 Motor 2 Max Output Frequency 40.0 to 400.0 Hz <2>E3-05 Motor 2 Max Voltage 0.0 to 255.0 <1> <2>E3-06 Motor 2 Base Frequency 0.0 to [E3-04] <2>E3-07 Motor 2 Mid Output Frequency 0.0 to [E3-04] <2>E3-08 Motor 2 Mid Output Frequency Voltage 0.0 to 255.0 <1> <2>E3-09 Motor 2 Minimum Output Frequency 0.0 to [E3-04] <2>E3-10 Motor 2 Minimum Output Frequency Voltage 0.0 to 255.0 <1> <2>E3-11 Motor 2 Mid Output Frequency 2 0.0 to [E3-04] 0.0 Hz <4>E3-12 Motor 2 Mid Output Frequency Voltage 2 0.0 to 255.0 <1> 0.0 V <3> <4>E3-13 Motor 2 Base Voltage 0.0 to 255.0 <1> 0.0 V <3>No. Parameter Name Setting Range DefaultE4-01 Motor 2 Rated Current 10 to 200% of the drive rated current. Determined by C6-01 ando2-04Output (V)Frequency (Hz)E3-05E3-12E3-13E3-08E3-10E3-09 E3-07 E3-06 E3-11 E3-04