Icom IC-7100 Advanced Instructions

Also see for IC-7100: Finger touch operation Specification Basic Manual Service manual Instruction manual

Contents

Icom IC-7100 Advanced Instructions Manual pdf 356 page image

20 CONTROL COMMAND20-3D Command tableRemote jack (CI-V) information (Continued)Cmd. Sub cmd. Data Description00 see p. 20-11 Send the operating frequency fortransceive01 see p. 20-11 Send the operating mode fortransceive02 see p. 20-12 Read the band edge frequencies03 see p. 20-11 Read the operating frequency04 see p. 20-11 Read the operating mode05 see p. 20-11 Send the operating frequency06 00 Select the LSB mode01 Select the USB mode02 Select the AM mode03 Select the CW mode04 Select the RTTY mode05 Select the FM mode06 Select the WFM mode07 Select the CW-R mode08 Select the RTTY-R mode17 Select the DV mode07 Select the VFO mode00 Select VFO A01 Select VFO BA0 Equalize VFO A and VFO BB0 Exchange VFO A and VFO B08 Select the Memory mode0001 to0109Select the Memory channel( 0001=M-CH01 to 0099=M-CH99,0100=1A, 0101=1B, 0102=2A,0103=2B, 0104=3A, 0105=3B,0106=144-C1, 0107=144-C2,0108=430-C1, 0109=430-C2)A0 01 Select Memory Bank A02 Select Memory Bank B03 Select Memory Bank C04 Select Memory Bank D05 Select Memory Bank E09 Memory write0A Memory copy to VFO0B Memory clear0C Read offset frequency0D Send offset frequency0E 00 Scan stop01 Programmed/memory scan start02 Programmed scan start03 ∂F scan start12 Fine programmed scan start13 Fine ∂F scan start22 Memory scan start23 Select memory scan start24 Mode select scan startA1 Set the ±5 kHz ∂F scan spanA2 Set the ±10 kHz ∂F scan spanA3 Set the ±20 kHz ∂F scan spanA4 Set the ±50 kHz ∂F scan spanA5 Set the ±100 kHz ∂F scan spanA6 Set the ±500 kHz ∂F scan spanA7 Set the ±1 MHz ∂F scan spanB0 Set as the Non-select Memory channelB1 Set as the Select Memory channelD0 Set Scan resume function OFFD3 Set Scan resume function ONCmd. Sub cmd. Data Description0F 00 Read Split function OFF01 Read Split function ON11 Read DUP– operation12 Read DUP+ operation00 Set Split function OFF01 Set Split function ON10 Set the simplex operation11 Set DUP– operation12 Set DUP+ operation10 00 Send/read the 10 Hz (1 Hz) tuningstep01 Send/read the 0.1 kHz tuning step02 Send/read the 1 kHz tuning step03 Send/read the 5 kHz tuning step04 Send/read the 6.25 kHz tuning step05 Send/read the 9 kHz tuning step06 Send/read the 10 kHz tuning step07 Send/read the 12.5 kHz tuning step08 Send/read the 20 kHz tuning step09 Send/read the 25 kHz tuning step10 Send/read the 50 kHz tuning step11 Send/read the 100 kHz tuning step12 Send/read the 1 MHz tuning step11 00 Send/read Attenuator OFF12 Send/read 12 dB attenuator13 00 Announce the operating frequency,operating mode and S-meter levelby voice synthesizer01 Announce the operating frequencyand S meter level by voice synthe-sizer02 Announce the operating mode byvoice synthesizer14 01 0000 to0255Send/read the AF level(0000=min. to 0255=max.)02 0000 to0255Send/read the RF gain level(0000=min., 0255=max.)03 0000 to0255Send/read the squelch level(0000=min. to 0255=max.)06 0000 to0255Send/read the NR level(0000=0% to 0255=100%)07 0000 to0255Send/read the inner [TWIN PBT]position( 0000=Cutting the higher passbandedge, 0128=center, 0255=Cuttingthe lower passband edge)08 0000 to0255Send/read the outer [TWIN PBT]position( 0000=Cutting the higher passbandedge, 0128=center, 0255=Cuttingthe lower passband edge)09 0000 to0255Send/read the CW PITCH( 0000=300 Hz, 0128=600 Hz,0255=900 Hz)0A 0000 to0255Send/read the RF power level(0000=min. to 0255=max.)0B 0000 to0255Send/read the MIC gain level(0000=min. to 0255=max.)0C 0000 to0255Send/read the KEY SPEED(0000=6 WPM to 0255=48 WPM)0D 0000 to0255Send/read the NOTCH setting( 0000=lowest, 0128=center,0255=highest)