44 • Vacon apfiff09 marineTel. +3585P2.4.2.26 Inching 1 0.1 0.1 531Inching reference 1 (DefaultForward 2 Hz. See P2.4.16). Thiswill start the drive.P2.4.2.27 Inching 2 0.1 0.1 532Inching reference 2 (DefaultReverse -2 Hz. See P2.4.17). Thiswill start the drive.P2.4.2.28 Motoring Power limit 1 0.1 0.1 1500 Activates power limit 1P2.4.2.29 Motoring Power limit 2 0.1 0.1 1501 Activates power limit 2P2.4.2.30 2nd frequency Limit 0.1 0.1 1511 Activates second freq. LimitP2.2.7.31 2nd Freq LimitP2.4.2.31 Generator Power Limit 1 0.1 0.1 1506 Activates Gen. power limit 1P2.4.2.32 Generator Power Limit 2 0.1 0.1 1507 Activates Gen. power limit 2P2.4.2.33 Reset Position 0.1 0.1 1090P2.4.2.34 MF Mode 2 0.1 0.1 1092P2.4.2.35 Emergency Stop 0.1 0.2 1213P2.4.2.36 Motoring Torque Limit 1 0.1 0.1 1624P2.4.2.37 Generator Torque Limit 1 0.1 0.1 1626P2.4.2.38 PID Activation 0.1 0.1 1804P2.4.2.39 Store Parameter Set 0.1 0.1 1753 Stores active parameter set toselected parameter setP2.4.2.40 Start Place A/B 0.1 0.1 425 Changes start signals between Aand B places.P2.4.2.41 Start signal 1B 0.1 A.1 403 Forward, See ID300P2.4.2.42 Start signal 2B 0.1 A.2 404 Reverse. See ID300P2.4.2.43 RunRequest Enable 0.1 0.2 1896Table 6-6. Digital input signals, G2.2.46.4.3 Analogue input 1Code Parameter Min Max Unit Default Cust ID NoteP2.4.3.1 AI1 signal selection 0.1 E.10 A.1 377 Slot . Board input No.P2.4.3.2 AI1 Reference FilterTC 0,000 32,000 s 0,000 324 0=No filteringP2.4.3.3 AI1 signal range 0 3 0 320012= -3= Custom range*P2.4.3.4 AI1 customminimum setting -160,00 160,00 % 0,00 321 Custom Range:Minimum inputP2.4.3.5 AI1 custommaximum setting -160,00 160,00 % 100,00 322 Custom Range:Maximum inputP2.4.3.6AI1 referencescaling, minimumvalue0,00 320,00 Hz 0,00 303Selects the frequencythat corresponds to themin. reference signalP2.4.3.7AI1 referencescaling, maximumvalue0,00 320,00 Hz 0,00 304Selects the frequencythat corresponds to themax. reference signalP2.4.3.8 AI1 joystick DeadZone 0,00 20,00 % 0,00 384 Dead Zone for joystickinputP2.4.3.9 AI1 sleep limit 0,00 100,00 % 0,00 385 Drive goest to stop ifinput is below this limitfor this time.P2.4.3.10 AI1 sleep delay 0,00 320,00 s 0,00 386P2.4.3.11 AI1 joystick offset -100,00 100,00 % 0,00 165 Press enter for 1s to setoffsetP2.4.3.12 AI1 filter time 0,000 32,000 s 0,000 1228Table 6-7. Analogue input 1 parameters, G2.2.2 *Remember to place jumpers of block X2 accordingly.See NX User's Manual, chapter 6.2.2.2
