Panasonic AG-HPX300 Operating Instructions Manual

Also see for AG-HPX300: Brochure & specs

Contents

151Maintenance and Inspections : Warning SystemMaintenance and Inspections9. 1394 ErrorDisplay windowindicationThe 1394 E-¢¢ indicator in the displaywindow blinks. For more information, see[1394 Error Codes] (page 152).WARNING lamp Blinks 4 times per second while theWARNING lamp recording is continuing.Tally lamp Blinks 4 times per second while the TALLYLAMP recording is continuing.ViewfinderIn the case of Error Code 92, “1394 INITIALERROR” indicator lights up (during pauseand recording)For Error Codes other than Error Code 92, orif REC SIGNAL is set to “1394”, no error isdisplayed in the viewfinder.Warning tone Beeps 4 times per second while ALARMrecording is continuing.WarningdescriptionThis indicates a failure of the DVCPROconnector.Recording/playbackoperationThe operation continues, but input signals tothe DVCPRO connector are abnormal. Formore information, see [1394 Error Codes](page 152).CountermeasuresCheck the connection between theIEEE1394 cable and the DVCPROconnector, settings of any external deviceand menus, and the turn on the power again.If the warning indication is still illuminated,confirm the “ 1394 Error Codes” (page 152),and consult your distributor.12. P2 Card ErrorDisplay windowindicationIf the error occurs during recording,“00:0000:11” appears as the time codeindication. The indication continues to flashafter recording is stopped and until the nextoperation is performed. There is noindication if the error occurs during playback.WARNING lampIf the error occurs during recording, the lampflashes four times per second for a period ofabout three seconds. The lamp does notlight if the error occurs during playback.Tally lampIf the error occurs during recording, the lampflashes four times per second for a period ofabout three seconds. The lamp does notlight if the error occurs during playback.ViewfinderA flashing “CARD ERR ¢” appears. In theactual indication the ¢ is replaced by the slotnumber of the P2 card that triggered the error.Warning toneIf the error occurs during recording, the tonesounds four times per second for a period ofabout three seconds. The tone does notsound if the error occurs during playback.WarningdescriptionAn error has occurred while recording datato or playing data from a P2 card.Recording/playbackoperationStop recording or playback. After recordingis stopped, the P2 card where error occurs iswrite protected.Countermeasures Replace the affected P2 card.10. Battery Nearly EmptyDisplay windowindicationOne of the bars in the battery remainingindicator starts blinking.WARNING lamp Blinks once per second.Tally lamp Blinks once per second.Viewfinder The BATT LED blinks.Warning tone Beeps 4 times per second.Warningdescription The battery is about to run out.Recording/playbackoperationContinues to operate.Countermeasures Replace the battery as required.13. FAN STOPDisplay windowindicationNo display.WARNING lamp Blinks 4 times per second.Tally lamp No display.Viewfinder The FAN STOP indicator blinks whilerecording continues.Warning tone It does not sound.WarningdescriptionThe fan is at rest because something iswrong with it.Recording/playbackoperationIf the camera-recorder operates with the fanstopped, then the temperature inside rises.While the camera-recorder continues tooperate, clips may not be recorded or playedback properly.Countermeasures Immediately stop using the camera-recorderand consult your distributor.11. P2 Card Nearly FullDisplay windowindicationOne of the bars for remaining MEDIAcapacity starts blinking.WARNING lamp Blinks once per second while recordingcontinues.Tally lamp Blinks once per second while recordingcontinues.Viewfinder The P2 card remaining capacity indicator blinks.Warning tone Beeps once per second while recordingcontinues.WarningdescriptionThe total remaining capacity of all the P2cards is two minutes or less.Recording/playbackoperationContinues to operate.Countermeasures Replace the cards. If there is an empty cardslot, insert a new card.