Panasonic AG-MD830E Service Manual

(JlCounterindicatorNo.10081009SuperimposedmonitorHI-FI RECAUDIO DUBSetting (underlin-ing denotes de- Description of functionfault setting)00 : OFF01 : ON00 : CH1.CH201 CH102 : CH2Hi-Fi audio recording (Cannot be used for audio DUB)OFF: Hi-Fi audio is not recorded.ON: Hi-Fi audio is recorded.Selection of channel track for audio dubbingCH1.CH2: The sound is added to CH1 and CH2 simul-taneously.CH1: The sound is added to CH1.CH2: The sound is added to CH2.1010 EDIT 00 : OFF (regular Editing/regular operation selectionSee Note 1 operation) OFF: Regular operation01 : ON (editing/ ON: For editing or dubbing_________________ .... _______________________ d.ubbi.nJ!l_________________ . __ .... __________________________________ .1011 NOTCH 00 : OFF For setting the NOTCH ON or OFFSee Note 2 01 ON OFF: ?NoTCH OFFON: NOTCH ONThe items shown below are displayed when the AG-IA823 serial interface board is used.CounterindicatorNo.SuperimposedmonitorSetting (underlin-Ing denotes de- Description of functionfault setting)... _---------------------_._-----------.----_ .... _-------------------------._ .. - _... _--------------------_.- .. _---_._--3001 BIT LENGTH3002 STOP BIT3003 PARITY3004 BAUD RATENotes:00 : 7BIT01 : 8BIT00 STOP-101 : STOP-200 : ODD01 EVEN02 : NONE00 : 120001 : 240002 : 480003 : 9600Character length setting7BIT: 7 bits8BIT: 8 bitsStop bit settingSTOP-1: 1 bitSTOP-2: 2 bitsParity bit settingODD: OddEVEN: EvenNONE: NoneBaud rate setting1200: 1200 bps2400: 2400 bps4800: 4800 bps9600: 9600 bps1. Edit function: When this is set ON, the noise reduction circuit for the video signals is set OFF. (The video noise will increase!ilightly. For regular use, EDIT OFF recommended.)2: NOTCH: When there is high level of noise in the luminance signals, it may also affect the chrominance signals. In a case likethis, set the NOTCH to ON. Since the luminance signal band is reduced slightly when the filter is set to ON, theNOTCH OFF position is recommended for regular use.-E-10-Counter Section00Memory StopRESET MEMO BEGIN ENDDODO,.,.,"To use the AUTO MEMORY STOP function:1. Press the MEMORY Button (MEMO)To turn on the MEMORY STOP function, the followingsyrnbol "-" will be indicated in Ihe counter display.2. When the VTR is placed in record a VISS signal willbe placed on the video tape.3. Now when the video tape is rewound or fastforwarded it will stop at the slart of any recording.4. This function can be turned off by pressing theMEMORY Button (MEMO).5. Repeat playback is covered on page E-13.MEMOoPress this to turn on"MEMORY STOP:"EWBE]Press either REW or FF.The tape stopsautomatically at the VISSwrite point or BGN setpoint.Each time the MEMORY Button isMEt pressed. the mode changes in thefoHowing sequence:·-VtSS"Memory stopj1·time memory repeatjContinuous repeatINo indication (OFF)This blinks while the VISS signalis being written on the tape.11 lights when VISS is set on themenu.Counter ResetThe counter display is reset to "0:00:00" when theRESET Button is pressed. The BGN/END setting isalso set to "0:00:00".RESETo rl·nrl·rlrl!...I· L.IL.I· L.I !...I.Remaining Tape"TAPE REMAIN" provides a rough indication of theamount of tape remaining. The indication appears about40 seconds after recording or playback has commenced(it does not appear until this time).TAPE REMAINI-----IFTape end Tape beginningEach lamp going off oneafter another indicatesthat the tape isapproaching its end.Note: The remaining tape indicator provides only arough indication: it is not meant to be precise.- E-11 -OPERATING INSTRUCTIONS