TallyGenicom SprintPro 2280+ manuals
SprintPro 2280+
Table of contents
SprintPro 2280+
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Introduction
- About this manual
- Printer at a glance
- Printer in tractor mode
- Paperway
- Installation
- Placing your printer
- Checking the printer voltage
- Switching on the printer
- Inserting the ribbon cassette
- Changing the ribbon cassette
- Printer drivers
- Installing a printer driver in Windows 2000/2003/XP
- Other operating systems
- Changing printer settings
- Loading optional firmware
- The control panel
- The LC display
- Online mode
- Setup mode
- Messages in the LC display
- Key functions when turning on the printer
- Paper handling
- Changing the paper type in the setup menu
- Loading paper
- Single sheets
- Paper transport
- Moving the paper to the tear position
- Removing paper
- Settings
- Setting the tear position
- Setting the first printing line (TOF)
- Selecting character density and font
- T model
- Loading paper into the rear tractor
- Paper guiding bracket
- The Menu
- Menu configurations
- Menu handling
- Selecting the LC display language
- Terminating Setup mode
- Menu structure
- Menu parameters
- Reset to default values (Reset)
- Selecting font (Font)
- Setting character density (CPI)
- Skiping perforation (Skip)
- Selecting emulation (Emulate)
- Settings for interfaces (I/O)
- Data format (Format)
- Further Settings (Special)
- Signal feedback (Remote)
- Protocol (Protocol)
- Selecting interface (Interf.)
- Ethernet interface (ETH-INT)
- Setting Subnet mask (Subnet)
- IP address administration (IP Get M)
- Selecting character set (CG-Tab)
- National character set (Country)
- Automatic carriage return (Auto-CR)
- Menu lock (MenLock)
- Paper parameters (Paper)
- First printing position (FormAdj)
- Printhead gap manually (Head)
- View and tear position (AutoTear)
- Line length (Width)
- Normal characters and barcode (Barmode)
- Form feed mode (FFmode)
- Setting and activating options (PapOpt)
- Activation of automatic sheet feeder (AutoASF)
- Menu settings (example)
- Advanced menu
- Printer self-test (Rolling ASCII)
- Exiting Rolling ASCII test mode
- Interface test (Hex-Dump)
- Terminating Hex-Dump
- Advanced settings
- Automatic paper motion sensor (PMS)
- Form length (Forml)
- Paper handling (Paphand)
- Paper width (Pagewid)
- Right-hand area (Rightzo)
- Bidirectional parallel interface (CX-bid)
- Beep at paper end (Sound)
- Settings for paper with dark back (Pap.back)
- Automatic paper width detection (APW)
- Automatic detection of the top paper margin (AED)
- Troubleshooting
- General print problems
- Problems with the paper feed
- Paper jam (single sheets)
- Problems with the print quality
- Error messages via the display
- Additional display messages
- Care and maintenance
- Cleaning the housing
- Cleaning the platen
- Cleaning the upper friction
- Specifications
- Interface specifications
- Paper specifications
- Character sets
- MTPL standard character set
- MTPL, international substitution characters
- OCR-A character set
- OCR-B character set
- Available character sets and fonts
- Emulations
- What are escape sequences
- How are escape sequences used
- List of available control codes
- Barcode
- US Postnet barcode
- KIX barcode
- LC printing
- List of additional control codes
- Interfaces
- Parallel interface
- Ethernet interface
- Physical printer port in Ethernet with TCP/IP
- Serial interface V.24/RS232C
- Interface cable (serial interface)
- Protocols
- ENQ/STX protocol
- Options and accessories
- Paper basket
- Accessories
- Index
- Table Of Contents
- Table Of Contents
manualsdatabase
Your AI-powered manual search engine