Kenwood TK-2170 Series Function Reference

Also see for TK-2170 SERIES: Service manual Instruction manual Instruction manual Specifications Service manual

19 2-TONEFUNC (K)/Ver. 1.01 Confidential Contents Index 7719.2.2 Duration of 2nd ToneThe Duration of 2nd Tone can be used to configure the2nd Tone Encode duration for transmitting the 2-toneconfigured for the 2-tone Encode Memory List.The Duration of 2nd Tone can be configured by usingKPG-101D. Normally, the Duration of 2nd Tone isconfigured for 3 seconds. Configuration using KPG-101D• Configuring the Duration of 2nd Tone (Refer toFPRG 6.11.1 Encode Tab - Duration of 2nd Tone.)19.2.3 Duration of Single ToneThe Duration of Single Tone is the Single Tone Encodeduration for transmitting the Single Tone configured forthe 2-tone Encode Memory List.The Duration of Single Tone can be configured by usingKPG-101D. Normally, the Duration of Single Tone isconfigured for 5 seconds. Configuration using KPG-101D• Configuring the Duration of Single Tone (Refer toFPRG 6.11.1 Encode Tab - Duration of SingleTone.)19.2.4 Gap TimeThe Gap Time can be used to configure the period of nomodulation between the 1st Tone and 2nd Tone used fortransmitting the 2-tone configured in the 2-tone EncodeMemory List.The Gap Time can be configured by using KPG-101D.Normally, the Gap Time is configured for 0 ms. Configuration using KPG-101D• Configuring the Gap Time (Refer to FPRG 6.11.1Encode Tab - Gap Time.)19.2.5 First Tone Delay TimeThe First Digit Delay Time is the time between when thetransceiver starts transmitting a 2-tone and when thetransceiver actually starts transmitting the 2-tone tone.During the First Tone Delay Time, the transceivertransmits an unmodulated signal.The First Tone Delay Time can be configured by usingKPG-101D. Configuration using KPG-101D• Configuring the First Tone Delay Time (Refer toFPRG 6.11.1 Encode Tab - First Tone DelayTime.)19.2.6 SidetoneSidetone can be used to monitor the 2-tone tones whenthe transceiver transmits 2-tone signaling.The Sidetone can be configured to be monitored by usingKPG-101D. Configuration using KPG-101D• Configuring the Sidetone (Refer to FPRG 6.11.1Encode Tab - Sidetone.)19.2.7 2-tone Encode Memory List2-tone Encode Memory List is the code list for encodingthe 2-tone. The transceiver transmits the 2-tone whenthe code configured for the list is selected.The following functions can be configured for the 2-toneEncode Memory List.Table 19-1 2-tone Encode Memory List Configuration Configuration using KPG-101D• Configuring the Single Tone (Refer to FPRG6.11.1 Encode Tab - Single Tone.)• Configuring the 2-tone Name (Refer to FPRG6.11.1 Encode Tab - 2-tone Name.)• Configuring the 1st Tone (Refer to FPRG 6.11.1Encode Tab - 1st Tone.)• Configuring the 2nd Tone (Refer to FPRG 6.11.1Encode Tab - 2nd Tone.)2-tone EncodeMemory List OperationSingle ToneThe code sent for each list number can beconfigured as a Single Tone. 2nd Tonecannot be configured if Single Tone isconfigured.2-tone Name2-tone Name can be used to assign a nameto each list number. A maximum of 8characters can be configured for the2-tone Name.1st ToneThe 1st Tone frequency can be configured.The frequency can be configured between288.5 and 3106.0 Hz.2nd ToneThe 2nd Tone frequency can be configured.The frequency can be configured between288.5 and 3106.0 Hz.2nd Tone cannot be configured if SingleTone is configured.