April 20172-86 Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer012-213, 012-221B, 012-223BLaunch IssueStatus Indicator RAPsEnter dC330 code 012-263. Manually rotate the encoder, PL 13.15 Item 19 to actuate thestacker encoder sensor. The display changes.Y NCheck the wiring between J8875 pin 2 and P/J8988 pin 23 for an open or short circuit, ora loose or damaged connector. The wiring is good.Y NReconnect or repair as necessary.Measure the voltage between P/J8988 pins 22 and 24 on the finisher PWB. The voltageis approximately +5VDC.Y NInstall a new finisher PWB, PL 13.45 Item 2.Measure the voltage between P/J8988 pin 23 on the finisher PWB and ground. Manuallyrotate the encoder, PL 13.15 Item 19 to actuate the stacker encoder sensor. The voltagechanges.Y NInstall a new stacker encoder sensor, PL 13.15 Item 32.Install a new finisher PWB, PL 13.45 Item 2.Enter dC330 code 012-262. Actuate the stacker no paper sensor, PL 13.15 Item 32. The dis-play changes.Y NCheck the wiring between J8872 pin 2 and P/J8988 pin 14 for an open or short circuit, ora loose or damaged connector. The wiring is good.Y NReconnect or repair as necessary.Measure the voltage between P/J8988 pins 13 and 15 on the finisher PWB. The voltageis approximately +5VDC.Y NInstall a new finisher PWB, PL 13.45 Item 2.Measure the voltage between P/J8988 pin 14 on the finisher PWB and ground. Actuatethe stacker no paper sensor. The voltage changes.Y NInstall a new stacker no paper sensor, PL 13.15 Item 32.Install a new finisher PWB, PL 13.45 Item 2.Install a new finisher PWB, PL 13.45 Item 2.012-221B, 012-223B Front Tamper Home Sensor Fail RAPBSD-ON: BSD 13.3 Office Finisher LX Interlock SwitchingBSD-ON: BSD 13.9 Office Finisher LX Tamping and Offset (1 of 2)BSD-ON: BSD 13.10 Office Finisher LX Tamping and Offset (2 of 2)ProcedureNOTE: Ensure the correct RAP is performed, refer to the 012-221, 012-223 Front TamperHome Sensor Fail Entry RAP.WARNINGEnsure that the electricity to the machine is switched off while performing tasks that donot need electricity. Refer to GP 10. Disconnect the power cord. Electricity can causedeath or injury. Moving parts can cause injury.Manually operate the tamper mechanism. The tamper mechanism moves smoothly.Y NInstall a new components as necessary, PL 13.28.Enter dC330 code 012-220 front tamper home sensor. Manually operate the tamper mecha-nism to actuate the front tamper home sensor. The display changes.Y NCheck the wiring between J8881 pin 2 and J8984 pin 5 for an open or short circuit, or aloose or damaged connector. The wiring is good.Y NReconnect or repair as necessary.Measure the voltage between J8984 pins 6 and 4 on the finisher PWB. The voltage isapproximately +5VDC.Y NInstall a new finisher PWB, PL 13.45 Item 2.Measure the voltage between J8984 pin 5 on the finisher PWB and ground. Manuallyoperate the tamper mechanism to actuate the front tamper home sensor. The voltagechanges.Y NInstall a new front tamper home sensor, PL 13.28 Item 8.Install a new finisher PWB, PL 13.45 Item 2.Enter dC330 012-020 and 012-023 alternately. The front tamper motor runs.Y NMeasure the voltage between J8984 pin 19 on the finisher PWB and ground. The volt-age is approximately +24VDC.Y NMeasure the voltage between J8982 pin 4 on the finisher PWB and ground. Thevoltage is approximately +24VDC.AA B
