April 20172-61Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer 012-152AStatus Indicator RAPsLaunch Issue012-152A Compiler Exit Sensor On Jam RAPBSD-ON: BSD 12.3 Integrated Office Finisher TransportationInitial ActionsNOTE: Ensure the correct RAP is performed, refer to the 012-152 Compiler Exit Sensor OnJam Entry RAP.WARNINGEnsure that the electricity to the machine is switched off while performing tasks that donot need electricity. Refer to GP 10. Disconnect the power cord. Electricity can causedeath or injury. Moving parts can cause injury.• Check the compiler exit sensor, PL 12.12 Item 16 is correctly installed and free from for-eign objects and that the actuator is not broken.• Switch off, then switch on the machine, GP 10.ProcedureCheck the specifications of paper, GP 15. Paper is in specification.Y NLoad paper that is in specification.Check the condition of the paper. The paper is in normal condition without any problemthat causes the paper to be bent or caught.Y NResolve any problem that causes the paper to be bent or caught.Check the transport path for a foreign object, deformed part, and paper dust. The transportpath is good.Y NRepair the deformed part(s) and remove the foreign object(s) and paper dust.Check the exit roll, PL 12.11 Item 10 for wear, deterioration or paper dust. The exit roll isgood.Y NRemove the paper dust or install a new exit roll, PL 12.11 Item 10.Check the drive mechanism to the transport roll for a deformed parts, broken parts, and/or beltdamage. The drive mechanism is good.Y NRepair defects or damage to the drive mechanism. Install new components as necessary,PL 12.11.Check that the finisher is installed correctly. The finisher is correctly installed and correctlyconnected to the IOT.Y NReinstall the finisher correctly.Enter dC330 code 012-150. Actuate the compiler exit sensor. The display changes.Y NCheck the connections of P/J8709 and P/J8728. The connectors are good.Y NSecure the connections.Check for an open or short circuit between P/J8709 and P/J8728. The wiring is good.Y NRepair the open or short circuit.Measure the voltage between the finisher PWB P/J8709 pin 3 (+) and ground (-). Thevoltage is approximately +5VDC.Y NCheck the +5VDC circuit. Refer to the Wiring Diagrams.Measure the voltage between the finisher PWB P/J8709 pin 2 (+) and ground (-). Actuatethe compiler exit sensor. The voltage changes.Y NInstall a new compiler exit sensor, PL 12.12 Item 16.Check the wires and connectors for an intermittent open or short circuit. If the fault per-sists, install a new finisher PWB, PL 12.14 Item 1.Enter dC330 code 012-095. The finisher transport motor runs.Y NCheck the connections of P/J8706 and P/J8739. The connectors are good.Y NSecure the connections.Check for an open or short circuit between P/J8706 and P/J8739. The wiring is good.Y NRepair the open or short circuit.Measure the voltage between the finisher PWB P/J8706 pin 5 (+) and ground (-), and P/J8706 pin 7 (+) and ground (-). Each voltage is approximately +24VDC.Y NCheck the +24VDC circuit. Refer to the Wiring Diagrams.Check the wires and connectors for an intermittent open or short circuit. If the fault per-sists, install a new components as necessary:• Finisher transport motor, PL 12.11 Item 17.• Finisher PWB, PL 12.14 Item 1.Check the wires and connectors for an intermittent open or short circuit. If the fault persists,install a new finisher PWB, PL 12.14 Item 1.
