August 20076-307WorkCentre 5687 Family dC330General Procedures & InformationdC330 Component ControlPurposeTo show the status of input components e.g. sensors, and to energies and exercise outputcomponents e.g. motors, solenoids.DescriptionOutput and input component codes are entered into the Component Control Table on the UI,and then energized individually or in permitted groups. The codes in the tables are grouped infunction chain (GP 2) order.Go to the appropriate procedure:• Input Components• Output ComponentsInput ComponentsWhen the appropriate code is entered the status of the component will be shown on the UI.NOTE: The logic level shown on the circuit diagrams with the signal name will be the actualsignal as measured with a service meter. This will not necessarily be the same as the logicstate shown on the UI, especially where the output is inverted. When testing components usingthese control codes, look for a change in state, not for a high or low.The displayed status of the input component can be changed by causing the component statusto change, e.g. operating a sensor with a sheet of paper. When a sensor is operated a beepwill sound.Go to the appropriate table:• Table 1 Input codes 01• Table 2 Input Codes 05• Table 3 Input Codes 06• Table 4 Input Codes 07• Table 5 Input Codes 08• Table 6 Input Codes 09• Table 7 Input Codes 10• Table 8 Input Codes 11• Table 9 Input Codes 12• Table 10 Input Codes 14Output ComponentsWhen the appropriate code is entered, the component will energize for a set time and then stopto protect the components. The default time-out for most components is set at 90 s, but can beas short as 5 s. Some components require that other components are energized at the sametime and it is possible to enter and energize up to six component control codes (not fax), butonly in permitted groups. If illegal combination of codes are entered the illegal codes will notenergize.Go to the appropriate table:• Table 11 Output Codes 04• Table 12 Output Codes 05• Table 13 Output Codes 06• Table 14 Output Codes 07• Table 15 Output Codes 08• Table 16 Output Codes 09• Table 17 Output Codes 10• Table 18 Output Codes 11• Table 19 Output Codes 12• Table 20 Output Codes 14• Table 21 Output Codes 20ProcedureCAUTIONDo not press Exit before stopping any energized components. The UI may lock up and greyout. If this occurs, switch off the machine, GP 14 and remove the power cord. Reconnect thepower cord and switch on the machine GP 14.1. Enter Diagnostics, GP 1.2. Select Diagnostics Routines.3. Select required dC routine category:• Copier Routines, 330 Component Control.• Fax dC Routines, 330 Component Control.4. Select and input the required codes as follows:NOTE: After a fault condition it may be necessary to switch off the machine and switch onthe machine (GP 14) for the codes to operate.NOTE: To clear an incorrectly entered code and reset the Add Component button to00.000, press the hard key C.a. From the component control Input Components tables and the Output Componentstables, select and enter the appropriate code into the Add Component button, andtouch the button. This will add the component to the top of the Component Nametable list, and when the list is full; the addition of more components will cause com-ponents to be deleted from the bottom of the list.NOTE: Fax component control codes can only be energized one at a time.b. If a control code is not known, it can be selected from the list displayed when theFind Component button is touched, as follows:NOTE: The ‘Find Component’ button is not available if components are energized.i. Enter the chain number into the Chain: button and touch the Find Componentbutton to display the control codes for that chain.ii. Use the scroll buttons to locate the required code, touch the Component Namebutton to highlight it and touch Select.iii. Repeat as required to add components to the Component Name table.iv. Touch Save to save the selections to the Component Name table list and returnto the Component Control window.5. To energize a component or group of components:a. Touch the control code to highlight it.b. Touch Start.
