August 20072-270 WorkCentre 5687 Family10-135, 10-136, 10-137, 10-138Status Indicator RAPs10-135, 10-136, 10-137, 10-138 Trail edge Late from InverterSensor RAP10-135 The trail edge of the paper failed to de-actuate the inverter sensor within the correcttime, for a simplex non invert sheet.10-136 The trail edge of the paper failed to de-actuate the inverter sensor within the correcttime, for a simplex inverted sheet.10-137 The trail edge of the paper failed to de-actuate the inverter sensor within the correcttime, for a duplex sheet side 1.10-138 The trail edge of the paper failed to de-actuate the inverter sensor within the correcttime, for a duplex sheet side 2.WARNINGDo not touch the fuser while it is hot.Initial Actions• Check the condition of the paper in all trays. Refer to IQ1 and GP 20.NOTE: If the fault occurs only with heavy weight paper of 120 gsm (32 lb.) or greater thatare being inverted, enter the Tools Mode and Stock Settings. Change the stock type toheavyweight for the appropriate tray. If the problem persists, perform the procedure in thisRAP.• Check for obstructions in the inverter area, Figure 1.• Check the upper and lower gravity fingers in the inverter, Figure 3, GP 7.• Check for obstructions in the exit area.• If the fault is caused by a multifeed of sheets, go to OF8 Multifeed RAP.ProcedureWARNINGTake care during this procedure. Motors will become hot during normal operation.NOTE: Ensure that the door interlock switch is cheated when checking +24V components.Enter dC330 code 10-105 inverter sensor, Q10-105. Press Start. Manually actuate the sensor.The display changes.Y NGo to Flag 1. Check Q10-120. Refer to:• GP 11 How to Check a Sensor.• Figure 3.• P/J61, IOT PWB.• 01E +5V Distribution RAP.• 01B 0V Distribution RAP.Install new components as necessary:• Inverter sensor, PL 10.12 Item 19.• Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL1.10 Item 2.Enter dC330 code 10-050 inverter nip solenoid, SOL10-050. Press Start. The solenoid ener-gises.Y NGo to Flag 2. Check SOL10-050. Refer to:• GP 12 How to Check a Solenoid or Clutch.• Figure 1.• P/J5, IOT PWB.• P/J17, LVPS.• Fuse, PL 1.10 Item 9, GP 7.• 01G +24V Distribution RAP.• 01B 0V Distribution RAP.Install new components as necessary:• Inverter nip solenoid, PL 10.11 Item 6.• Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL1.10 Item 2.Enter dC330 code 10-045 inverter path solenoid, SOL 10-045. Press Start. The solenoidenergizes.Y NGo to Flag 3. Check SOL 10-045. Refer to:• GP 12 How to Check a Solenoid or Clutch.• Figure 1.• P/J5, IOT PWB• P/J17, LVPS.• Fuse, PL 1.10 Item 9, GP 7.• 01G +24V Distribution RAP.• 01B 0V Distribution RAP.Install new components as necessary:• Inverter path solenoid, PL 10.11 Item 14.• Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL1.10 Item 2.Enter dC330 code 10-055 tri-roll nip split solenoid, SOL 10-055. Press Start. The solenoidenergizes.Y NGo to Flag 5. Check SOL 10-055. Refer to:• GP 12 How to Check a Solenoid or Clutch.• Figure 3.• P/J61, IOT PWB• P/J17, LVPS.• Fuse, PL 1.10 Item 9, GP 7.• 01G +24V Distribution RAP.• 01B 0V Distribution RAP.Install new components as necessary:• Tri-roll nip split solenoid, PL 10.14 Item 1.AAB
