8.2 Drive Options and Peripheral DevicesYASKAWA ELECTRIC SIEP C710616 27C YASKAWA AC Drive A1000 Technical Manual 375Peripheral Devices &Options88.2 Drive Options and Peripheral DevicesThe following table of peripheral devices lists the names of the various accessories and options available for Yaskawadrives. Contact Yaskawa or your Yaskawa agent to order these peripheral devices.• Peripheral Device Selection: Refer to the Yaskawa catalog for selection and part numbers.• Peripheral Device Installation: Refer to the corresponding option manual for installation instructions.Option Model Number DescriptionPower OptionsDC Reactor - Improves the power factor by suppressing harmonic distortion from the powersupply.AC Reactor -Protects the drive when operating from a large power supply and improves thepower factor by suppressing harmonic distortion. Highly recommended for powersupplies that exceed 600 kVA.Braking Resistor ERF-150WJ Series For use with systems that require dynamic braking with up to 3% ED. If higherED is required, use a Braking Resistor Unit.Braking Unit CDBR Series External braking transistorInput / Output Option CardsAnalog Input AI-A3Allows high precision, high resolution analog reference input.Input channels: 3Voltage input: -10 to 10 Vdc (20 kΩ), 13 bit signedCurrent input: 4 to 20 mA or 0 to 20 mA (250 kΩ), 12 bitAnalog Monitor AO-A3Provides extra multi-function analog output terminals.Output channels: 2Output voltage: -10 to 10 V, 11 bit (signed)Digital Input DI-A3Used to set the frequency reference by digital inputsInput channels: 18 (including SET signal and SIGN signal)Input signal type: BCD 16 bit (4 digit), 12 bit (3 digit), 8 bit (2 digit)Input signal: 24 Vdc, 8 mADigital Output DO-A3Provides extra insulated multi-function digital outputs.Photocoupler relays: 6 (48 V, up to 50 mA)Contact relays: 2 (250 Vac/up to 1 A, 30 Vdc/up to 1 A)Motor Speed Feedback Option CardsComplementary PG PG-B3For speed feedback input by connecting a motor encoderInput: 3 track (can be used with one or two tracks), for HTL encoder connection,50 kHz maxOutput: 3 track, open collectorEncoder power supply: 12 V, max current 200 mALine Driver PG PG-X3For speed feedback input by connecting a motor encoderInput: 3 track (can be used with one or two tracks), line driver, 300 kHz maxOutput: 3 track, line driverEncoder power supply: 5 V or 12 V, max current 200 mACommunication Options CardsPROFIBUS-DP SI-P3 Connects to a PROFIBUS-DP network.CC-Link SI-C3 Connects to a CC-Link networkDeviceNet SI-N3 Connects to a DeviceNet networkCANopen SI-S3 Connects to a CANopen networkMECHATROLINK-II SI-T3 Connects to a MECHATROLINK-II networkInterface OptionsLED Operator JVOP-182 5-digits LED operator; max. cable length for remote usage: 3 mRemote Operator Cable WV001/WV003 Extension cable (1 m or 3 m) to connect the digital operator for remote operationRJ-45, 8 pin straight through, UTP CAT5e cableUSB Copy Unit JVOP-181 Allows the user to copy and verify parameter settings between drives. Can also beused as an adapter to connect the drive to the USB port on a PC.Mechanical OptionsAttachment for External Heatsink EZZ020786 Installation kit for mounting the drive with the heatsink outside of the panel (Side-by-Side mounting possible)NEMA 1 Kit EZZ020787 Parts to make the drive conform to NEMA Type 1 enclosure requirementsInstallation Support Set A EZZ020642A For installing the digital operator keypad on the outside of an enclosure panel thathouses the drive. Also refer to Digital Operator Remote Installation on page 43.Installation Support Set B EZZ020642BOthers24 V Power Supply PS-A10L, PS-A10H Option to supply the drive controller with 24 Vdc power during main power lossPC Software ToolsDriveWizard Plus Contact Yaskawa PC tool for drive setup and parameter managementDriveWorksEZ Contact Yaskawa PC tool for enhanced programming of the drive
