B.3 Parameter TableYASKAWA ELECTRIC SIEP C710616 27C YASKAWA AC Drive A1000 Technical Manual 423Parameter ListB◆ H Parameters: Multi-Function TerminalsH parameters assign functions to the multi-function input and output terminals.■ H1: Multi-Function Digital InputsF6-53(3C4H) DeviceNet PPA SettingSets the format of the data set from the drive to the DeviceNet master.Default: 71Min: 0Max: 255–F6-54(3C5H)DeviceNet Idle Mode FaultDetection 0: Enabled1: Disabled, no fault detectionDefault: 0Min: 0Max: 1–F6-55(3C6H) DeviceNet Baud Rate Monitor Used to verify the baud rate running on the network.0: 125 kbps1: 250 kbps2: 500 kbpsDefault: 0Min: 0Max: 2–F6-56(3D7H) DeviceNet Speed ScalingSets the scaling factor for the speed monitor in DeviceNet.Default: 0Min: -15Max: 15–F6-57(3D8H) DeviceNet Current ScalingSets the scaling factor for the output current monitor in DeviceNet.Default: 0Min: -15Max: 15–F6-58(3D9H) DeviceNet Torque ScalingSets the scaling factor for the torque monitor in DeviceNet.Default: 0Min: -15Max: 15–F6-59(3DAH) DeviceNet Power ScalingSets the scaling factor for the power monitor in DeviceNet.Default: 0Min: -15Max: 15–F6-60(3DBH) DeviceNet Voltage ScalingSets the scaling factor for the voltage monitor in DeviceNet.Default: 0Min: -15Max: 15–F6-61(3DCH) DeviceNet Time ScalingSets the scaling factor for the time monitor in DeviceNet.Default: 0Min: -15Max: 15–F6-62(3DDH) DeviceNet Heartbeat IntervalSets the heartbeat interval for DeviceNet communications.Default: 0Min: 0Max: 10–F6-63(3DEH) DeviceNet Network MAC IDUsed to verify the MAC ID the drive has been assigned.Default: 0Min: 0Max: 63–F6-64 toF6-71(3DFH to3C8H)ReservedReserved for Dynamic I/O Assembly Parameters.– –<3> Parameter setting value is not reset to the default value when the drive is initialized.No.(Addr.) Name Description Setting PageH1-01(438H)<31> Value in parenthesis is the default setting when a 3-wire initialization is performed (A1-03 = 3330).Multi-Function Digital InputTerminal S1 Function SelectionAssigns a function to the multi-function digital inputs.Refer to H1 Multi-Function Digital Input Selections on page 424 for a description of settingvalues.Note: Unused terminals should be set to F.Default: 40 (F) <31>Min: 1Max: 9F214H1-02(439H)Multi-Function Digital InputTerminal S2 Function SelectionDefault: 41 (F) <31>Min: 1Max: 9F214H1-03(400H)Multi-Function Digital InputTerminal S3 Function SelectionDefault: 24Min: 0Max: 9F214H1-04(401H)Multi-Function Digital InputTerminal S4 Function SelectionDefault: 14Min: 0Max: 9F214H1-05(402H)Multi-Function Digital InputTerminal S5 Function SelectionDefault: 3(0) <31>Min: 0Max: 9F214H1-06(403H)Multi-Function Digital InputTerminal S6 Function SelectionDefault: 4(3) <31>Min: 0Max: 9F214H1-07(404H)Multi-Function Digital InputTerminal S7 Function SelectionDefault: 6(4) <31>Min: 0Max: 9F214H1-08(405H)Multi-Function Digital InputTerminal S8 Function SelectionDefault: 8Min: 0Max: 9F214No.(Addr.) Name Description Setting PageAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes common_TMonlyAll Modes
