B.3 Parameter Table418 YASKAWA ELECTRIC SIEP C710616 27C YASKAWA AC Drive A1000 Technical Manual◆ F: OptionsF parameters are used to program the drive for PG feedback from the motor and to function with option cards.■ F1: PG Speed Control Card (PG-B3 / PG-X3)Parameters F1-01, F1-05, F1-06, F1-12, F1-13, and F1-18 through F1-21 are used to set up a PG option card plugged intooption connector CN5-C of the drive. They include “PG 1” in the parameter name.Parameters F1-21 through F1-37 are used to set up a PG option card plugged into option connector CN5-B of the drive.They include “PG 2” in the parameter name.Other parameters in the F1 group are used to set operation for PG options plugged into connector CN5-C and CN5-B.E5-11(333H) Encoder Z-pulse OffsetSets the offset between the rotor magnetic axis and the Z pulse of an incremental encoder. Setduring Z Pulse Offset Tuning.Default: 0.0 degMin: -180 degMax: 180 deg205E5-24(353H)<3>Motor Induction Voltage Constant2 Set the induced phase-to-phase rms voltage in units of 0.1 mV/(r/min) [mechanical angle]. Setthis parameter when using a Yaskawa SMRA Series SPM motor.When setting this parameter, E5-09 should be set to 0.Default: <14>Min: 0.0 mV/(r/min)Max: 2000.0 mV/(r/min)205<3> Parameter setting value is not reset to the default value when the drive is initialized.<4> Default setting is dependent on the control mode (A1-02), the drive model (o2-04), and the Drive Duty (C6-01).<14> Default setting value is dependent on the motor code set to E5-01.<19> This value's number of decimal places depends on the drive model and the Heavy/Normal duty selection in parameter C6-01. The value willhave two decimal places (0.01 A) if the drive is set for a Maximum Applicable Motor Capacity up to 11 kW (refer to Table A.2 and Table A.3)and one decimal place (0.1 A) if the set Maximum Applicable Motor Capacity is higher than 11 kW.<23> If using a Yaskawa SMRA Series SPM Motor, the default setting is 1800 r/min.<28> Selection may vary depending on the motor code entered to E5-01.No.(Addr.) Name Description Setting PageF1-01(380H) PG 1 Pulses Per RevolutionSets the number of PG (pulse generator or encoder) pulses.Sets the number of pulses per motor revolution.Default: <10>Min: 0 pprMax: 60000 ppr206F1-02(381H)Operation Selection at PG OpenCircuit (PGo)0: Ramp to stop. Decelerate to stop using the deceleration time in C1-02.1: Coast to stop.2: Fast Stop. Decelerate to stop using the deceleration time in C1-09.3: Alarm only.4: No alarm display.Note: Due to potential damage to motor and machinery, the "Alarm only" and "No alarmdisplay" setting should be used only under special circumstances.Default: 1Min: 0Max: 4206F1-03(382H)Operation Selection at Overspeed(oS) 0: Ramp to stop. Decelerate to stop using the deceleration time in C1-02.1: Coast to stop.2: Fast Stop. Decelerate to stop using the deceleration time in C1-09.3: Alarm only.Default: 1Min: 0Max: 3206F1-04(383H) Operation Selection at Deviation 0: Ramp to stop. Decelerate to stop using the deceleration time in C1-02.1: Coast to stop.2: Fast Stop. Decelerate to stop using the deceleration time in C1-09.3: Alarm only.Default: 3Min: 0Max: 3207F1-05(384H) PG 1 Rotation Selection0: Pulse A leads1: Pulse B leadsDefault: <10>Min: 0Max: 1207F1-06(385H)PG 1 Division Rate for PG PulseMonitor Sets the division ratio for the pulse monitor used of the PG option card installed to connectorCN5-C. By setting “xyz”, the division ratio becomes = [(1 + x) / yz]. If only using the A pulsefor one track input, then the input ratio will be 1:1, regardless of what F1-06 is set to.Default: 1Min: 1Max: 132207No.(Addr.) Name Description Setting PageOLV/PM AOLV/PMCLVV/f w/PGCLV/PMV/f OLV common_TMonlyOLV/PM AOLV/PMCLVV/f w/PGCLV/PMV/f OLV common_TMonlyOLV/PM AOLV/PMCLVV/f w/PGCLV/PMV/f OLV common_TMonlyOLV/PM AOLV/PMCLVV/f w/PGCLV/PMV/f OLV common_TMonlyOLV/PM AOLV/PMCLVV/f w/PGCLV/PMV/f OLV common_TMonlyOLV/PM AOLV/PMCLVV/f w/PGCLV/PMV/f OLV common_TMonlyOLV/PM AOLV/PMCLVV/f w/PGCLV/PMV/f OLV common_TMonlyOLV/PM AOLV/PMCLVV/f w/PGCLV/PMV/f OLV common_TMonly
